Volvo Penta 13L Operator'S Manual Download Page 81 | Manualshive

Page: 81 / 122

background image

Charge Air Pipe, Leakage Check

Inspect the condition of the charge air hoses, hose
unions and clamps for cracks and other damage.
Change as necessary.

Clamps must be tightened using a torque wrench to
9 ±2 Nm (6.6 ±1.5 lbf.ft.).

Drive Belt and Alternator Belt,
Inspection

WARNING!

Working with or approaching a running engine is a
safety risk. Watch out for rotating components and hot
surfaces.

IMPORTANT:

Always change a belt which looks worn or cracked.

Inspections must be carried out after operations, while
the belts are hot.
You should be able to depress the alternator belt and
the drive belt about 3-4 mm between the pulleys.
The alternator belts and drive belts have automatic belt
tensioners and do not need to be adjusted.
Check the condition of the drive belts. Replace as
necessary; refer to

Alternator Belt, Replace, page 81

Drive belt, change, page 80

Maintenance

79

47711089 09-2018 © AB VOLVO PENTA

«
...
79
80
81
82
83
...
»

Summary of Contents for 13L



























































































































Reviews:

No comments

Related manuals for 13L

Brand: O.S. engine Pages: 5

MAX-15CV-R Series

Brand: O.S. engine Pages: 19

3T-MOTORS 3T45-20

Brand: 3T-Components Pages: 24

Brand: Hatz Diesel Pages: 48

Brand: Kohler Pages: 85

Brand: Mitsubishi Electric Pages: 102

marine TM.5.8TS

Brand: Toyama Pages: 88

Brand: ARRI Pages: 28

Brand: GMC Pages: 7

Brand: AE Pages: 4

Brand: Quectel Pages: 37

Brand: O.S. engine Pages: 4

Brand: O.S. engine Pages: 4

Brand: O.S. engine Pages: 17

Brand: O.S. engine Pages: 21

Brand: O.S. engine Pages: 21

Brand: O.S. engine Pages: 21

Brand: O.S. engine Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands