Voltec Pro Pure Sine Wave Owner'S Manual Download Page 1

 

Pure Sine Wave Power Inverter 

OWNER’S MANUAL

 

 

 

Featured Design 

 

High efficiency- save battery   

 

Compact size- portable 

 

Low Idle Current 

 

Soft Start Technology 

 

 

 
THIS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING 
SAFETY, OPERATION, MAINTENANCE AND STORAGE  OF THIS 
PRODUCT. BEFORE USE, READ AND UNDERSTAND ALL CAUTIONS, 
WARNINGS, INSTRUCTIONS AND PRODUCT LABELS, PLUS YOUR 
VEHICLE’S BATTERY MANUFACTURER GUIDELINES. FAILURE TO DO 
SO COULD RESULT IN INJURY AND/OR PROPERTY DAMAGE. 
 
 
 

IMPORTANT SAFETY INSTRUCTIONS 

To ensure reliable service, your power inverter must be installed and used properly. 
Please read the installation and operating instructions thoroughly prior to 
installation and use. Pay particular attention to the WARNING and CAUTION 
statements in this manual.  The CAUTION statements advise against certain 
conditions and practices that may result in damage to your inverter. The WARNING 
statements identify conditions or practices that may result in personal injury.  

Read 

All Instructions Before Using This Power Inverter!

 

 

 

Summary of Contents for Pure Sine Wave












Reviews: