• The power adapter must never be plugged in or disconnected when your hands
are wet.
• Never unplug the power adapter from the mains socket by pulling on the cable;
always use the grips on the plug.
• When setting up the product, ensure that the cable is not pinched, kinked or dam-
aged by sharp edges.
• Always lay the cables so that nobody can trip over or become entangled in them.
This poses a risk of injury.
• For safety reasons, disconnect the power unit from the mains socket during
storms.
•
Neverpouranyliquidsoverelectricaldevicesorplaceobjectsfilledwithliquidnext
to the product. If liquid or an object does enter the interior of the device, power
down the respective socket (e.g. switch off circuit breaker), and remove the mains
plug from the mains socket. Discontinue use and take the product to a specialist
repair centre.
• Never use the product immediately after it has been brought from a cold room into
a warm one. The condensation generated could destroy the product. The power
adapter may also generate a fatal electric shock! Allow the product to reach room
temperature before connecting it to an appliance. This may take several hours.
• Make sure to observe the polarity and magnitude of the output voltage. Incorrect
polarityorexcessivevoltageinputleadstothedestructionoftheconnectedelectri
-
cal appliance.
•
Sufficientventilationisessentialwhenoperatingtheproduct.Donotcoverthe
product. Never place the product on a table cloth or on a carpet! Place it on a hard,
flameresistantbase.
• Unplug the mains plug from the mains socket under the following conditions:
-Before you clean the product
-During a thunder storm
-
Iftheproductisnotusedoveranextendedperiodoftime
•
Consultanexpertwhenindoubtabouttheoperation,safetyorconnectionofthe
appliance.
•
Maintenance,modificationsandrepairsmustonlybecompletedbyatechnicianor
an authorised repair centre.
• If you have questions which remain unanswered by these operating instructions,
contact our technical support service or other technical personnel.
b) Connected Devices
• Also observe the safety and operating instructions of any other devices which are
connected to the product.
Operation
Disconnect the power supply unit from the mains socket before replacing the low-
voltage plug or resetting the output voltage.
The power supply unit’s output voltage must match the input voltage of the electric
consumer.
USB devices and other electric loads can be operated in parallel. However, make
surethatthepowerinputoftheconnecteddevicesdoesnotexceedthepowersup
-
ply unit’s total power output.
a) Connecting an electric load
• Set the required output voltage with the voltage selection switch, using the voltage setting
key. When making settings, always be sure the arrow points accurately to the respective
voltage marking.
• Select one of the nine low-voltage plugs matching the input socket and polarity of the elec-
tric consumer (see table).
• Connect the plug to the connector at the end of the output cable. Voltage reversal of the
output plug is not possible for security reasons. The inner contact is positive (+), the outer
negative (–).
• Connect the low-voltage plug to the switched-off consumer.
• Connect the power cord’s low-voltage plug with the matching socket of the power supply
unit.
• Connect the mains plug to a standard mains socket. The LED on the top of the power supply
unit indicates operational readiness.
•
Putthepowersupplyunitontoasolid,flame-retardantsurfaceandensurethatthepower
supplyunitissufficientlyventilated.
• Now switch the connected consumer on. If it does not function properly, switch it off im-
mediately and disconnect it from the power supply unit.
• Remove the power supply unit from the mains when it is no longer in use.
Operating Instructions
NPS-90-1-N Notebook power adapter
Item No. 2266530
Intended Use
This product is designed to supply USB devices and other electric devices such as notebooks
or netbooks with power, providing eleven different output voltages to select from. The con-
nectedload’scurrentconsumptionmustnotexceedthemaximumoutputratingoftheproduct.
Power is supplied via a standard mains socket. The product should only be used in dry indoor
areas. The product features both short-circuit and overload protection.
It is intended for indoor use only. Do not use it outdoors. Contact with moisture, e.g. in bath-
rooms, must be avoided under all circumstances.
For safety and approval purposes, you must not rebuild and/or modify this product. If you use
the product for purposes other than those described above, the product may be damaged. In
addition,improperusecanresultinshortcircuits,fires,electricshocksorotherhazards.Read
the instructions carefully and store them in a safe place. Make this product available to third
parties only together with its operating instructions.
This product complies with the statutory national and European requirements. All company
names and product names are trademarks of their respective owners. All rights reserved.
Delivery Content
• Power adaptor
• Voltage setting key
• Power cable
•
9xLow-voltageplugs
• Operating instructions
Up-to-date Operating Instructions
Download the latest operating instructions at www.conrad.com/downloads or
scan the QR code shown. Follow the instructions on the website.
Explanation of Symbols
The symbol with the lightning in the triangle is used if there is a risk to your health,
e.g. due to an electric shock.
Thesymbolwiththeexclamationmarkinthetriangleisusedtoindicateimportant
information in these operating instructions. Always read this information carefully.
The arrow symbol indicates special information and advice on operation.
Safety Instructions
Read the operating instructions carefully and especially observe the safety in-
formation. If you do not follow the safety instructions and information on proper
handling in this manual, we assume no liability for any resulting personal injury
or damage to property. Such cases will invalidate the warranty/guarantee.
a) General Information
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. This may become dan-
gerous playing material for children.
•
Protecttheappliancefromextremetemperatures,directsunlight,strongjolts,high
humidity,moisture,flammablegases,steamandsolvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of operation and
protect it from any accidental use. Safe operation can no longer be guaranteed if
the product:
- is visibly damaged,
-is no longer working properly,
-
hasbeenstoredforextendedperiodsinpoorambientconditionsor
-has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height
can damage the product.
• Make sure that the adapter output is not short-circuited.
• Do not touch the power adapter if there are any signs of damage, as this may
cause a fatal electric shock! First, switch off the mains voltage to the socket to
which the mains adapter is connected (switch off at the corresponding circuit
breaker or remove the safety fuse, and then switch off at the corresponding RCD
protective switch, so the socket is fully disconnected). You can then unplug the
power adapter from the mains socket. Dispose of the faulty power adapter in an
environmentally friendly manner and discontinue use. Replace it with a power
adapter of the same design.
• The mains socket must be located near to the device and be easily accessible.
• Only connect the power adaptor to a normal mains socket connected to the public
supply. Before plugging in the power adapter, check whether the voltage stated on
the power adapter complies with the voltage of your electricity supplier.
