VOLTCRAFT DSO-2104 User Manual Download Page 16

Page: 16 / 66

3.Quick Start

Caution:

The default attenuation coefficient of the probe on the instrument is
preset to 10X.

Make sure that the set value of the attenuation switch in the probe is
the same as the menu selection of the probe attenuation coefficient in
the oscilloscope.

The set values of the probe switch are 1X and 10X (see

Figure 3-8

Figure 3-8 Attenuation Switch

Caution:

When

the attenuation switch is set to 1X, the probe will limit the

bandwidth of the oscilloscope in 5MHz. To use the full bandwidth of
the oscilloscope, the switch must be set to 10X.

How to Use the Probe Safely

The safety guard ring around the probe body protects your finger against any
electric shock, shown as

Figure 3-9

Figure 3-9 Finger Guard

Warning:

To avoid electric shock, always keep your finger behind the safety
guard ring of the probe during the operation.

To protect you from suffering from the electric shock, do not touch any
metal part of the probe tip when it is connected to the power supply.

Before making any measurements, always connect the probe to the
instrument and connect the ground terminal to the earth.

Summary of Contents for DSO-2104



































































Search results

Summary of Contents for DSO-2104

Reviews:

Related manuals for DSO-2104

Brands by name

Popular brands

VOLTCRAFT DSO-2104, User Manual

Search results

Summary of Contents for DSO-2104

Reviews:

Related manuals for DSO-2104

Brands by name

Popular brands