Voltask SB-EA Manual Download Page 4

-This power tool may only be used with the accessory parts listed under accessories.

-This product is not intended for commercial use, Generally acknowledged accident prevention 

  regulations and  endorsed safety instructions must be observed.

-Only perform work described in these instructions for use. Any other use is improper. 

-The manufacturer will not assume responsibility for damage resulting from such use.

INTRODUCTION

PACKAGE CONTENTS

INTRODUCTION-PACKAGE CONTENTS       01

Snow

Thrower × 1

 Assembly × 1 

Accessories

Package × 1

User Manual × 1 

Warranty card

× 1 

Carefully remove the snow thrower and check to see that all of the above items are supplied. 

  

Properly dispose of these materials in accordance with local regulations.

IMPORTANT! 

The equipment and packaging material are not toys. Do not let children play with plastic 

bags, foils or small parts. These items can be swallowed and pose a suffocation risk! 

NOTE: 

Do not discard the shipping carton and packaging material until you are ready to use your new 

snow thrower. The packaging is made of recyclable materials.

Troubleshooting

× 1 

Summary of Contents for SB-EA


























Reviews: