background image

INSTALLATION INSTRUCTIONS

w w w . v o l t l i g h t i n g . c o m

- 10 -

VOLT

® 

RGBW Max All-Star Integrated LED Spotlight

VAL-2045-ABK

2

IR Remote Functions

1. On/Off

2. Brightness Control

3. 16 color selections

4. Flash

 

Mode 1: Repeats Red, Green, Blue + color cycle for 1 second duration of 

each of the seven colors within this mode.

 

Mode 2: Hit flash a second time and this mode slowly blends the same 

seven colors from mode one, mixing them together.

5. Strobe

 

Mode 1: Pick any color on the remote, then press strobe and that color 

will strobe every second alternating between on and off.

 

Mode 2: Hit strobe a second time and this mode will strobe a blended 

white color at the same speed as before.

6. Fade

 

Mode 1:  Pick any color on the remote, then press fade and that color 

will slowly fade in and out every second.

 

Mode 2:  Hit fade a second time and it will fade a blended white color in 

and out at the same speed as before.

 

7. Smooth

 

Mode 1: Repeats a flash cycle of Red, Green, and Blue only.

 

Mode 2: Hit smooth a second time and this mode slowly blends Red, 

Green, and Blue only; in and out of each other at the same speed.

NOTE: When using the 

remote make sure it is 

pointed at the sensor on 

the back of the fixture so it 

operates properly. 

Summary of Contents for RGBW Max All-Star VAL-2045-ABK













Reviews: