background image

Page 2

 

 SHILOH™

 

Vogelzang International Corp.

 

TR002B | 20120125.0

SAFETY INSTRUCTIONS-Read All Instructions Carefully.

1.  The installation of this stove must comply with your 

local building code rulings. Please observe the clear-
ances to combustibles (see reference figures 10–12). 
Do not place fuel, furniture or any other objects within 
the clearance area.

2.  Verify that the stove is properly assembled and 

installed before firing the stove for the first time. 
After reading these instructions, if you have any 
doubt about your ability to complete your installation  
properly, you must obtain the services of a  
professional licensed installer familiar with all  
aspects of safe and correct installation.  DO NOT  
use temporar y or makeshift compromises  
during installation. There must be 

NO DEVIATION 

OR ALTERATION OF ANY KIND from the very spe-
cific instructions spelled out in this instruction manual 
as it pertains to the installation of this woodstove. 

 

NO EXCEPTIONS!

3.  DO NOT store wood, kindling, flammable liquids 

or other combustible materials in the vicinity of the 
appliance. Refer to certification label on back of unit 
and reference figures 10–12 in this manual.

4. 

DO NOT INSTALL THIS STOVE IN A MOBILE 
HOME, MANUFACTURED HOME, TRAILER OR 
TENT NO EXCEPTIONS! (HUD Federal Standard: 
24 CFR Ch.XX).

5. 

DO NOT ELEVATE THIS STOVE BY ANY MEANS. 
(i.e. bricks under pedestal base, cement blocks)  
Stove base must set directly upon the solid-surface, 
non-combustible floor as specified in this stove 
instruction manual. 

6. 

DO NOT MODIFY THIS STOVE IN ANY WAY! Stove 
must be installed with pedestal stand provided and 
attached as shown in the instructions. 

DO NOT OP-

ERATE WITHOUT ASH DRAWER OR ASH CLEAN 
OUT COVER IN PLACE 
– NO EXCEPTIONS. As-
semble only with original parts as supplied and shown 
in this manual. 

DO NOT OPERATE A STOVE THAT 

IS MISSING ANY PARTS! If any parts are missing 
or defective, please notify the dealer or manufacturer 
immediately. Replace missing, broken or worn parts 
with factory original or equivalent parts only.

7. 

CAUTION: DO NOT ALTER COMBUSTION AIR 
CONTROL RANGE TO INCREASE FIRING OR 
FOR ANY REASON. 
Altering or tampering with air 
control beyond normal capacity will create unsafe 
and hazardous conditions.

8.  Always connect this stove to a chimney and vent to 

the outside. Never vent to a room or inside a build-
ing. 

DO NOT CONNECT THIS UNIT TO A CHIMNEY 

FLUE SERVING ANOTHER APPLIANCE.

9. 

DO NOT CONNECT A WOOD BURNING STOVE TO 

AN ALUMINUM TYPE B GAS VENT. This is not safe. 
Use approved masonry or an Underwriters Labo-
ratories Listed UL 103 HT (US)/ULC-S629 (CDN) 
Residential Type and Building Heating Appliance 
Chimney. Use a 6˝/152mm diameter chimney, that 
is high enough to give a good draft. (See specifics 
in Chimney Connections instructions).

10.  Be sure that your chimney is safely constructed and 

in good repair. Have the chimney inspected by the fire 
department or a qualified inspector. Your insurance 
company should be able to recommend a qualified 
inspector. Chimney connector pipe must be in good 
condition. Replace if necessary before using stove.

11.  Creosote or soot may build up in the chimney con-

nector and chimney and cause a house/building 
fire. Inspect the chimney connector and chimney 
twice monthly during the heating season and clean 
if necessary. (see Service Hints). 

12.  In the event of a chimney fire, turn the air controls to 

closed positions, leave the building and 

CALL THE 

FIRE DEPARTMENT IMMEDIATELY!  Have a clearly 
understood plan on how to handle a chimney fire by 
contacting your local fire authority for information 
on proper procedures in the event of a chimney fire.  
After the fire is out, the chimney must be cleaned 
and inspected for any stress or cracks before starting 
another fire. Check the condition of any combustibles 
surrounding the chimney.

13.  Ashes should not be allowed to accumulate above 

the top of the lower primary air orifice (LPAO, air vent 
at front of firebox, just inside of door).

14. 

DISPOSAL OF ASHES  Ashes should be placed 
in a steel container with a tight fitting lid and moved 
outdoors immediately. The closed container of ashes 
should be placed on a noncombustible floor or on the 
ground, well away from all combustible materials, 
pending final disposal. If the ashes are disposed of 
by burial in soil or otherwise locally dispersed, they 
should be retained in the closed container until all 
cinders have completely cooled. Other waste shall 
not be placed in this container.

15.  To prevent injury, do not allow anyone to use this 

stove who is unfamiliar with the correct operation of 
the stove.

16.  Do not operate stove while under the influence of 

drugs or alcohol.

17. 

DO NOT ELEVATE THE FIRE. Build fire directly on 
the bottom of the firebox. This stove has not been 
tested with the use of grates, andirons or other means 
of elevating the fire and must not be used.

18. The special paints used on your stove may give 

off some smoke and an odor while they are cur-

Summary of Contents for TR002B



























Reviews: