47 2120
Arc test set
with
Electr. digital indicator
Operation manual
\\server-1\Daten5\Produkte\472120\Bedienungsanleitung\472120_en.doc
Measuring jaws Change
:
Select the corresponding sensor to mach the measured workpiece. There are 5 different measurement sensors for disposal:
10/20/30/60 and 100mm. After placing the indicator in the selected probe, turn the micrometer on.
With the button C (changeover sensor measurement-7) change their attitude accordingly.
If you have chosen the 30mm sensor, the indicator should be "C = 30" display.
Measuring operation:
Inside arc: the best measurement range
C=10
R=5»13mm
C=20
R=11»30mm
C=30
R=22»100mm
C=60
R=94»260mm
C=100 R=255»700mm
Outside arc: the best measuring range
C=10
R=6,5»15mm
C=20
R=14»30mm
C=30
R=27»100mm
C=60
R=94»260mm
C=100 R=255»700mm
Mode button:
Press the MODE button (5) and you can switch between inside- and outside arc.
The display shows “R1“for inside and “R2” for outside arc.
A = Indicator for radius
Please note. R1 and R2 will automatically switch.
Display
1. Display radius
2. Indication the length of the arc during measurement
Battery replacement:
Slide out the battery cover on the top side. Remove battery from the compartment and insert a new battery with the anode pointing
downwards. Insert battery cover very carefully.
Trouble shooting:
Error Cause
Correction
way
No display
1. Battery empty
2. Battery has no contact
1. Change battery
2. Clean contacts
LCD does not count
Fault in electronic
Take battery out and replace after 30 sec. or use
new battery.
Please note
:
Please prepare measuring very carefully. The device should de regularly cleaned with cotton-cloth.
Do not use petrol. Do not expose the device direct to the sun light, ultraviolet rays or extreme temperatures.
Prevent it from any shock and do not immerse the device in any liquid.
Electric etching or engraving by high voltage can destroy the electronic chip, no guarantee will be given!
Never dismantle the calliper housing. The battery should be taken out, if no use for a long time.
Do not give batteries and devices in refuse. Please give it to a special collecting depot.
Declaration of conformity and confirmation
of traceability
We declare under our sole responsibility that this product is in conformity with standards and technical data as specified in our sales documents
(operation instructions, leaflet and catalogue).
We certify that the measuring equipment used to check this product, and guaranteed by our Quality Assurance, refers to national standards.
Thank you very much for your confidence in purchasing this product.
47 2120
Radienprüfsatz
mit
Digital Messuhr
Bedienungsanleitung
\\server-1\Daten5\Produkte\472120\Bedienungsanleitung\472120_de.doc
Funktionen:
1. Hold Taste
2. Umschaltung mm/inch
3. Zero & ON/OFF Taste
4. Datenausgang Mini-USB-Stecker
5. Mode Taste
6. Batteriefachdeckel
7. Umschaltung Messfühler 10/20/30/60/100mm
8. Display
9. Feststellschraube
10. Basis
11. Messspitze
12. Messspindel
Spezifikationen:
Messbereich linear
0-13mm
Messbereich Radius
5-700 mm
Linear Abweichung
0,02 mm
Radius Abweichung
0,02 mm
Messkraft
< 1,50 N
Speisung
Batterie (3 V, CR2032, Artikel-Nr. 20 02093)
Betriebstemperatur
0°C bis 40°C
Lagertemperatur
-20°C bis 60°C
Luftfeuchtigkeit
d
80%
Erklärung:
C: Abstand Messfühler
S: Linearer Abstand Messfühler
R: Bogenradius
Einführung:
Mit diesem Radienprüfsatz, können Sie folgende Messungen durchführen_
-
Außenradius Messungen
-
Innenradius Messungen
-
Tiefen Messungen
-
Stufenmessungen
Hold Taste (1)
Drücken Sie die Hold-Taste (1) um den letzten gemessenen Wert zu speichern. Im Display erscheint das Symbol H.
Durch erneutes Drücken, kehrt die Messuhr in den Normalmodus zurück.
Umschaltung mm/inch
Durch Drücken der Taste mm/inch (2) kann zwischen den Maßeinheiten gewechselt werden.
Zero & ON/OFF Taste
Durch Drücken der Taste Zero & ON/OFF Taste (3) wird die Messuhr eingeschaltet bzw. ausgeschaltet.
Mit dieser Taste kann der Nullpunkt an jeder beliebigen Stelle gesetzt werden.
Die automatische Abschaltung erfolgt nach ca. 5 Minuten
.
D
i
s
t
r
i
b
u
t
o
r
Distributor
Kontakt
