background image

 

The  device  must  be  disconnected  from  the  supply  mains(where  appropriate) 
when removing the battery; 

 

The battery is to be disposed of safety; 

 

Using incorrect type batteries can cause damage to people or the accessory. 

 

FCC  

Caution:  

This equipment has been tested and found to comply with the limits for a Class B 
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to 
provide reasonable protection against harmful interference in a residential 
installation.  

This equipment generates uses and can radiate radio frequency energy and, if not 
installed and used in accordance with the instructions, may cause harmful 
interference to radio communications. However, there is no guarantee that 
interference will not occur in a particular installation. If this equipment does cause 
harmful interference to radio or television reception, which can be determined by 
turning the equipment off and on, the user is encouraged to try to correct the 
interference by one or more of the following measures:  

-- Reorient or relocate the receiving antenna.  

-- Increase the separation between the equipment and receiver.  

-- Connect the equipment into an outlet on a circuit different from that to which the 
receiver is connected.  

-- Consult the dealer or an experienced radio/TV technician for help.  

The antenna(s) used for this transmitter must be installed to provide a separation 
distance of at least 20 cm from all persons and must not be co-located or operating 
in conjunction with any other antenna or transmitter. 

This device complies with part 15 of the FCC Rules. Operation is subject to the 
following two conditions:  

(1) This device may not cause harmful interference  

(2) this device must accept any interference received, including interference that may 
cause undesired operation.  

Any Changes or modifications not expressly approved by the party responsible for 
compliance could void the user's authority to operate the equipment. 

 

Summary of Contents for VS1










Reviews: