ENG - 16
Mode & Level Settings
Function
LED Behavior
Description
Input Search
The LED indicator
color will change
per specifi c input.
SETUP > Input Srch > OK
to initiate an automatic input detection sequence. This is the
same as a long key press of the
INPUT
button on the remote. Specifi c inputs will show a
diff erent LED color:
• AUX In: Green
• AUX VA: Violet
• Digital Optical: Red
• HDMI 1: Yellow
• HDMI (eARC): Magenta
Program Remote
Learn
Waiting to learn:
Flash from bottom
to top and back
continuously.
SETUP > PrgRemote >
Use the
Next/Previous
buttons and
OK
button to toggle and
select and program your TV remote to control the
Volume Down
,
Volume Up
, and
Mute
functions on your sound bar. See the
Programing the Sound Bar on page 20 section for
more information.
Power LED
Power LED On
SETUP > PwrLED >
Use the
Next/Previous
buttons to enable/disable the Power LED.
Power LED Off
Announcements
Announcements On
SETUP > Anncment >
Use the
Next/Previous
buttons to enable/disable the voice
announcements.
Note
: Some voice announcements will still be turned on, such as “Subwoofer not found”
and “Bluetooth connecting.”
Announcements Off
AV Delay
LED at the bottom
indicates no delay.
SETUP > AV Delay >
Use the
Next/Previous
buttons to increase/decrease the amount of
audio delayx. The LED indicators will move to the top with increasing audio delay level.
Reset Audio or
Reset All
All LEDs will fl ash
3 times when
settings are reset.
SETUP > Reset Audio or Reset All >
Use the
Next/Previous
buttons to reset either Audio
or All settings. Press the
OK
button to select.
Audio
- Only audio settings, such as bass and treble levels, will be reset.
All
- All paired Bluetooth devices will be unpaired and all settings will be lost. All
programmed IR remotes will also be removed. See the
Factory Reset on page 19 for
more information.
Input Srch
Function
LED Behavior
Description
Speaker Test
—
SETUP > Spkr Test > OK
to activate the speaker test function. A voice will begin calling
out each speaker beginning with
left front (Left Front, Center, Right Front, Right Rear, Left
Rear, Left Front Height, Right Front Height, and subwoofer-white noise). If any of these are
missing, check the connection and run the speaker test function again.
VIZIO Remote
Remote On
SETUP > VZtvRmt >
Use the
Next/Previous
buttons to enable/disable VIZIO TV
Remotes. When enabled (On), you can use a VIZIO TV remote control to turn on the sound
bar (using the
TV Volume Up
button) and control volume.
Remote Off
Elevate Height
Speakers
EFFECT > Elvate >
Use the
Next/Previous
buttons to toggle between preset height modes.
Up -
Front height speakers will rotate up to provide an immersive movie sound experience.
Wide -
Front height speakers will rotate forward (good for listening to music).
Auto -
Setting will adjust height speakers based on content.
Note:
Default setting is Auto.
Elevate
Indicator LED
—
EFFECT > ElvLED >
Use the
Next/Previous
buttons to turn the Elevate indicator LED on,
off , or change its color.
Off -
Use the
Next/Previous
button to toggle to
OFF
and hit
OK
to turn the Elevat4e
Indicator off .
Next -
Use the
Next/Previous
button to toggle to
NEXT
and hit
OK
to cycle through
diff erent Elevate Indicator LED colors.
Note:
The Elevate Indicator LED is only active when aluminum end caps are rotated and
extended out from the sound bar. This happens when the Elevate Height Speakers are set
to Up or Auto (when Dolby Atmos content is playing).
Spkr Test
Elvate
ElvLED
VZtvRmt
PwrLED
Anncmnt
AV Delay
Prg Remote