Vivotek SD9363-EHL User Manual Download Page 71

Page: 71 / 332

VIVOTEK

71 - User's Manual

Primary DNS

: The primary domain name server that translates host names into IP addresses.

Secondary DNS

: Secondary domain name server that backs up the Primary DNS.

Primary WINS server

: The primary WINS server that maintains the database of computer names and IP

addresses.

Secondary WINS server

: The secondary WINS server that maintains the database of computer names

and IP addresses.

Enable UPnP presentation

: Select this option to enable UPnP

presentation for your Network Camera

so that whenever a Network Camera is presented to the LAN, the shortcuts to connected Network

Cameras will be listed in My Network Places. You can click the shortcut to link to the web browser.

Currently, UPnP

is supported by Windows XP or later. Note that to utilize this feature, please make

sure the UPnP

component is installed on your computer.

Enable UPnP port forwarding

: To access the Network Camera from the Internet, select this option to

allow the Network Camera to open ports automatically on the router so that video streams can be sent

out from a LAN. To utilize of this feature, make sure that your router supports UPnP

and it is activated.

PPPoE (Point-to-point over Ethernet)

Select this option to configure your Network Camera to make it accessible from anywhere as long as

there is an Internet connection. Note that to utilize this feature, it requires an account provided by your

ISP.

Follow the steps below to acquire your Network Camera’s public IP address.

1. Set up the Network Camera on the LAN.

2. Go to Configuration > Event > Event settings > Add server (please refer to Add server on page 118) to

add a new email or FTP server.

3. Go to Configuration > Event > Event settings > Add media (please refer to Add media on page 109).

Select System log so that you will receive the system log in TXT file format which contains the

Network Camera’s public IP address in your email or on the FTP server.

4. Go to Configuration > Network > General settings > Network type. Select PPPoE and enter the user

name and password provided by your ISP. Click

Save

to enable the setting.

5. The Network Camera will reboot.

6. Disconnect the power to the Network Camera; remove it from the LAN environment.

Mega-pixel Network Camera (192.168.5.151)

Summary of Contents for SD9363-EHL













































































































































































































































































































































Search results

Summary of Contents for SD9363-EHL

Reviews:

Related manuals for SD9363-EHL

Brands by name

Popular brands

Vivotek SD9363-EHL, User Manual

Search results

Summary of Contents for SD9363-EHL

Reviews:

Related manuals for SD9363-EHL

Brands by name

Popular brands