Vivotek FD8335H Quick Installation Manual Download Page 12

Page: 12 / 14

EN - 11

English

For further setup, please

refer to the user's

manual on the software

CD.

Ready to Use

1. A browser session with the Network Camera should prompt as shown below.
2. You should be able to see live video from your camera. You may also install the 32-channel recording

software from the software CD in a deployment consisting of multiple cameras. For its installation
details, please refer to its related documents.

Based on the live image retrieved from the camera, adjust the camera lens by doing the following:

To adjust the viewing angle -- 3-axis mechanism design

1. Loosen the tilt adjustment screws and then turn the lens module up or down. Upon completion,

tighten the screw.

2. Turn the lens to adjust the image orientation.

Adjusting the Lens

Horizontal Pan

350°

Lens Horizontal

Pan 350°

Vertical Tilt 80°

Tilt Adjustment

Screws

Summary of Contents for FD8335H















Search results

Summary of Contents for FD8335H

Reviews:

Related manuals for FD8335H

Brands by name

Popular brands

Vivotek FD8335H, Quick Installation Manual

Search results

Summary of Contents for FD8335H

Reviews:

Related manuals for FD8335H

Brands by name

Popular brands