Vitrum RailZ-4M, User Manual

Page: 4 / 36

STANDARDS AND REGULATIONS
Electrical safety (LVD) 2014/35/EU
Electromagnetic compatibility (EMC) 2014/30/EU
Radio
(RED) 2014/53/EU
Presence of hazardous
substances
(RoHS II) 2011/65/EU
Waste electrical and electronic
equipment
(WEEE) 2012/19/EU
Special condition or status
Normal operating condition or status
COMMAND CLASS BASIC SET: MAX Value = [0x63 o 0xFF] -> [par31->36]
COMMAND CLASS INDICATOR values 0-7,0xff
The version implemented is the #1 and may turn the device as a blinking
indicator. The supported values are 0x00 (off/disable) or 0xFF (on/enable)
and the field may carry valid values from 1 to 7.
0xFF: StartBlink(ALL_CHANNELS, YELLOW);
0x00: StopBlink(ALL_CHANNELS);
Valid values are:
1: white, 2: blue, 3: green, 4: cyan, 5: red, 6: magenta, 7: yellow
Timeout:
~
60s
Informations below Reported from Node Information Frame (NIF)
Informations below Reported from:
1. Node Information Frame (NIF)
2. Version CC, Version Get and Report commands
Informations below reported from Multi Channel Capability Report Command,
valid if endpoint is set as “CURTAIN” only.
Endpoints 1, 2, 3, set as “CURTAIN”, are linked with endpoints 4, 5, 6 in vertical
pairs, so endpoint 1 (direction up) is linked to endpoint 4 (direction down), and
so on. Therefore endpoint 4, 5, 6, will not be “INTEROPERABLE” if a multichannel
capability get is requested.
The valid endpoint association groups will be only 3, 4, 5. Relevant parameters
are 191-196.
Informations below reported from Multi Channel Capability Report Command:
Manufacturer ID: 0x010A
Wire the device according to the schematic below.
L
Power connection (LIVE)
N Power connection (Neutral)
EN 301 489-1 V1.9.2; EN 301 489-3 V1.6.1
EN 50491-5-1:2010; EN 50491-5-2:2010
EN 60669-1:2000; EN 60669-1/A1:2003; EN60669-1/A2:2009
EN 60669-2-1:2004; EN 60669-2-1/A1:2009; EN 60669-2-1/A12:2009
EN 62479: 2010
EN 300 220-2 V.2.4.1
Position the device in the wall’s mounting box and check cables are not
interfering with the device case. Using the appropriate screw set that
matches the wall box, fix the device in place without applying unnecessary
torque to fixing screws.
Do not locate the device facing direct sunlight, humid or dusty place. The
suitable ambient temperature is listed in specification.
Do not locate the device where there are any combustible substances or
sources of heat (e.g. fires, radiators, boiler, etc.).
Buttons and LEDs are numbered according the picture below facing front
the device.
Each button has an RGB back-light LED that shows different colours during
normal operation and certain sequence are also used to report special
status.
Button
#1
is used as
z-wave network button
SPECIFICATIONS
INSTALLATION
FUNCTIONS
NODE CAPABILITIES
Operating voltage 230 VAC 50 Hz
Consumption <1.5W standby
Operating temperature
from 0°C to +40°C
Operating Humidity
20% - 90% RH non condensing
Storage temperature
from -40°C to +55°C
Storage Humidity
10% - 93% RH non condensing
IP Class
IP20
Package Dimension (W x H x D)
Weight
~210 gr
RF radiated powered 2.5 mW (max)
RF range
Up to 40 m open range
Warranty
1 year
LED Colour codes Description
LED #1 blinks green for 5s Valid HW signature detected at boot
blinks red for 5s Invalid HW signature detected at boot
red glitch When button #1 is touched indicates device
is NOT included in the Z-Wave network
Steady red HW fault, contact assistance
LED Colour codes Description
Any LED
Steady blue BASIC off or MULTILEVEL 0%
Steady green light dimming MULTILEVEL set at 33%
Steady yellow MULTILEVEL set at 100% or BASIC on
Steady magenta MOTOR control
REGION CODE FREQUENCY
PRODUCT
TYPE ID
PRODUCT
ID
APP ID
EU
868.4 Mhz 0x7115 0x1016 0x0215
IL 916 Mhz 0x7006 0x0F07 0x0106
KR
921.4 Mhz 0x7116 0x1017 0x0216
NIF PARAMETER DESCRIPTOR LIBRARY IDENTIFIER
Basic Device Class BASIC_TYPE_ROUTING_SLAVE
Routing Slave Ennhanced 232
Generic Device Class GENERIC_TYPE_SWITCH_BINARY
Specific Device Class SPECIFIC_TYPE_POWER_SWITCH_BINARY
PARAMETER
DESCRIPTOR
DESCRIPTION LIBRARY IDENTIFIER
Generic Device
Class
Switch Multilevel GENERIC_TYPE_SWITCH_MUL-
TILEVEL
Specific Device
Class
Class A Motor
Control
SPECIFIC_TYPE_CLASS_A_MO-
TOR_CONTROL
COMMAND
CLASS
LIBRARY IDENTIFIER VERSION
Binary COMMAND_CLASS_SWITCH_BINARY 1
Multilevel Switch COMMAND_CLASS_SWITCH_MULTILEVEL 4
COMMAND CLASS LIBRARY IDENTIFIER VERSION
Z-Wave Plus Info COMMAND_CLASS_ZWAVEPLUS_INFO 2
Version COMMAND_CLASS_VERSION 2
Manufacturer Specific COMMAND_CLASS_MANUFACTURER_SPE-
CIFIC
2
Device Reset Locally COMMAND_CLASS_DEVICE_RESET_LOCALLY 1
Powerlevel COMMAND_CLASS_POWERLEVEL 1
Firmware Update
Meta Data
COMMAND_CLASS_FIRMWARE_UPDATE_MD 4
Association COMMAND_CLASS_ASSOCIATION 2
Multi Channel
Association
COMMAND_CLASS_MULTI_CHANNEL_AS-
SOCIATION
3
AGI (Association
Gorup Info)
COMMAND_CLASS_ASSOCIATION_GRP_
INFO
1
Multi Channel COMMAND_CLASS_MULTI_CHANNEL 4
Configuration COMMAND_CLASS_CONFIGURATION 1
Manufacturer
Proprietary
COMMAND_CLASS_MANUFACTURER_PRO-
PRIETARY
1
Indicator COMMAND_CLASS_INDICATOR 1
Node Name and
Location
COMMAND_CLASS_NODE_NAMING 1
All Switch COMMAND_CLASS_SWITCH_ALL 1
C
ommand
C
lass
m
ark
Scene Activation COMMAND_CLASS_SCENE_ACTIVATION 1
Central Scene COMMAND_CLASS_CENTRAL_SCENE 1
Multilevel Switch COMMAND_CLASS_SWITCH_MULTILEVEL 4
Binary Switch COMMAND_CLASS_SWITCH_BINARY 1
Basic COMMAND_CLASS_BASIC 1
Basic, Generic and Specific Device Class
Command Classes
Command Class Specification
Generic and Specific Device Class by Curtain Endpoint
SUPPORTED COMMAND CLASS BY ENDPOINT
Models and Frequencies
Technical Specifications
Choosing a suitable location
List of harmonized regulations applied
Example of End Point Type values:
Button configured as EP_CENTRAL_SCENE. It sends through the Lifeline
association group the “Central Scene Notification” commands. (CMD_Key_
Pressed,CMD_Key_Released,CMD_Key_Held_Down).
To set an EP_CENTRAL_SCENE use the Configuration command Class
parameter 1->6, value 0x1A.
DYNAMIC ENDPOINT EXPLANATION Description
Par. N.
(Dec)
Size
(B)
Value
range
Default
value
Button N.1 to N.6 On Color status 13 to 18 1 0-7 4
Button Eco Color
Button N.1 to N.6 Eco Color status 19 to 24 1 0-7 2
Button On/Off/Eco Color values list
LED_COLOR_OFF 0
LED_COLOR_RED 1
LED_COLOR_GREEN 2
LED_COLOR_BLU 3
LED_COLOR_YELLOW 4
LED_COLOR_MAGENTA 5
LED_COLOR_CYAN 6
LED_COLOR_WHITE 7
Button to Output Port connection
Output Port connected to Button N.1 to N.6 25 to 30 1 0-6
Output Port
Not connected to any port 0
Output Port N.1 to N.6 connected to button 1 to 6
Basic or Multilevel SET max value type 31 to 36
1
0 = 0x63
(100%)
1 = 0xFF
(last level)
0: 0x63
Motors Control Time
Channel 0 to 2 Motor Control Time (s) 191 to
193
1 60 (60 s)
Channel 0 Motor Control Switch All
behavior (*1)
194 1 0
Channel 1 Motor Control Switch All
behavior
195 1 0
Channel 2 Motor Control Switch All
behavior
196 1 0
Lifeline queue time delay:
Add some delay to lifeline notifications
215 2 1= 10 mS
10=100 mS
100=1000
mS
NWI Enable 216 1 1
: NWI enabled, default
0
: learn mode classic only
Multichannel Capability Report
notification:
Endpoint presentation after multichannel
transmission
217
1
0
:
disabled, default
1:
low power
2
:
Full Power
Keyboard Lock
O
utputs and back-light still working
1. Lifeline notification CCConfig[218, 1] If a
locked button is pressed
2. Force unlock: triple press on button 1 as per
inclusion process -> BIP.... BIP-BIP
218
1 0: unlock
1: lock
0: unlock
Triac safe mode
when an EP is transformed in to curtain the cor-
responding Triac is disabled (only for triac dev.)
221
1 0:unable
1:disable
N/A
110 x 72 x 62 mm
FAMIGLIA DIN
OPTIONAL
PT1000B
OPTIONAL
PT1000B
DOWN
UP
DOWN
UP
DOWN
UP
DOWN
UP
DOWN
UP
DOWN
UP
Code:
Z EU DD0 M02 0
Z IL DD0 M02 0
Z KR DD0 M02 0
Code:
Z EU DD0 M01 0
Z IL DD0 M01 0
Z KR DD0 M01 0
Code:
Z EU DD0 D01 0
Z IL DD0 D01 0
Z KR DD0 D01 0
Code:
Z EU DD0 D02 0
Z IL DD0 D02 0
Z KR DD0 D02 0
Code:
Z EU DD0 L02 0
Z IL DD0 L02 0
Z KR DD0 L02 0
Code:
Z EU DD0 H01 0
Z IL DD0 H01 0
Z KR DD0 H01 0
Code:
Z EU DD0 DL4 0
Z IL DD0 DL4 0
Z KR DD0 DL4 0
Code:
Z EU DD0 L04 0
Z IL DD0 L04 0
Z KR DD0 L04 0
DIN-RGB DIN-HVAC DIN-SW2 DIN-SW4
DIN-M2 DIN-M1
Immagine Default
DIN-HIV2
DIN-HIV1
ICONE
Not applicable
FAMIGLIA DIN
OPTIONAL
PT1000B
OPTIONAL
PT1000B
DOWN
UP
DOWN
UP
DOWN
UP
DOWN
UP
DOWN
UP
DOWN
UP
Co
de:
Z EU DD0 M02 0 Z IL DD0 M02 0 Z KR DD0 M02 0
Co
de:
Z EU DD0 M01 0 Z IL DD0 M01 0 Z KR DD0 M01 0
Co
de:
Z EU DD0 D01 0 Z IL DD0 D01 0 Z KR DD0 D01 0
Co
de:
Z EU DD0 D02 0 Z IL DD0 D02 0 Z KR DD0 D02 0
Co
de:
Z EU DD0 L02 0 Z IL DD0 L02 0 Z KR DD0 L02 0
Co
de:
Z EU DD0 H01 0 Z IL DD0 H01 0 Z KR DD0 H01 0
Co
de:
Z EU DD0 DL4 0 Z IL DD0 DL4 0 Z KR DD0 DL4 0
Co
de:
Z EU DD0 L04 0 Z IL DD0 L04 0 Z KR DD0 L04 0
DIN-R
GB
DIN-HV
A
C
DIN-SW2
DIN-SW4
DIN-M2
DIN-M1
Immagine Default
DIN-HIV2
DIN-HIV1
IC
ONE
01D02H010
01DE20010
01DB2H010