30
ASSEMBLY INSTRUCTIONS
Auxiliary handle
The auxiliary handle (13) can be mounted in two
different positions to adapt the power tool to the work
to be done and make easier its handling.
1.
Insert the clamping screw of the auxiliary handle into
one of the grinder fixing threads;
2.
Screw the auxiliary handle in clockwise until it is fully
tightened in place;
Disc guard
The position of the disc guard can be adjusted according
to suit the working conditions. The disc guard must be
fitted on the tool so that the closed side of the guard
always points toward the operator.
1.
Install the disc guard (14) with the protrusion on the
guard band aligned with the notch of the gear
housing (4);
2.
Turn the disc guard according to the desired position;
3.
Tighten the guard locking screw (3);
4.
To remove the disc guard, follow the installation
procedure in reverse;
Cutting and grinding discs
1.
Make sure that the disc guard (14) is securely fitted;
2.
Place the inner flange (2) onto the spindle. Make
sure that the inner flange is properly fitted on the
spindle;
3.
Fit the cutting disc (1) in the inner locking flange of
the disc. Make sure the disc is correctly installed;
4.
Place the outer flange of the disc (2) onto the spindle:
- For cutting discs, the outer locking flange of the disc
is placed with the protrusion facing away from the
disc;
- For grinding discs, the outer locking flange of the
disc is placed with the protrusion facing away from
the disc;
5.
Press the spindle lock button (5) and rotate the disc
by hand until it locks. Keep the spindle lock button
pressed in and tighten the outer flange with the
supplied spanner;
6.
As a precaution, perform a test to check the correct
installation of the rotating accessory;
7.
To remove the disc, follow the installation procedure
in reverse;
Wear
protective
gloves
when
installing
accessories;
OPERATING INSTRUCTIONS
The power tool has been designed to cut, sharpen, grind
and polish metal and stone materials without using
water.
While operating the appliance some precautions must
be taken into account:
▪
Always hold the angle grinder with both hands and
with the auxiliary handle installed;
▪
Do not apply too much pressure over the work
piece/object. The angle grinder’s weight is enough to
apply the necessary pressure. If speed drops
abruptly, the pressure should be reduced
immediately;
▪
Never turn the angle grinder on if the rotary
accessory is touching the workpiece. The rotary
accessory must not touch the workpiece until the
maximum speed has been reached;
▪
Keep an angle of 15° between the disc and the
workpiece surface; This procedure increases the
grinding capacity of the disc and will avoid
unnecessary overloading;
▪
Do not use water or grease during the sharpening
process;
▪
Do not use a cutting disc for grinding, and vice versa;
▪
To attach accessories to the spindle thread, make
sure that the rotating accessory thread (type and
dimensions) match the accessory thread;
▪
Do not use the cutting disc to sharpen sideways.
Cutting discs must not be subjected to any lateral
pressure;
▪
Use special care when working corners, sharp edges.
Prevent the accessory from bouncing or getting stuck
in the workpiece;
▪
The power cord must always be behind the appliance
during operation;
Summary of Contents for Pro-Power VIRE12510A
