background image

VITEK

VITEK

FEATURES

• 1/3” Megapixel Progressive Scan CMOS image sensor
• Up to 30fps live view
• 3.3~12mm Varifocal Lens (VTD-TND30R3V2) / 3.6-10mm 

Varifocal Lens (VTD-TND30R5V2) / Motorized 3.3-12mm 

Varifocal Lens (VTD-TND30R4M2)

• 30 Infrared LED’s with 100’ IR Range 
• 120dB Super Wide Dynamic Range (WDR)
• True Mechanical Day/Night function by ICR
• XD-DNR (2D-DNR & 3D-DNR) Noise Reduction 
• On Board Motion Detection
• H.265/H.264/MJPEG Triple Streaming
• Secondary Video Output (CVBS)
• Remote Viewing via CMS, Internet Explorer, and iOS & 

Android Apps

• Minimal Latency with up to 10 simultaneous user 

connections

• MicroSD memory card slot for Local recording supporting 

up to 128GB MicroSDXC cards

• ONVIF Compliant
• IP66 Weather Resistance
• Optional Wall Mount Available (VT-TWM03)
• 12VDC & PoE (Power over Ethernet) Operation

 VTD-TND30R3V2

VTD-TND30R5V2

VTD-TND30R4M2

3.0, 4.0, and 5.0 Megapixel 

Indoor/Outdoor WDR IP IR 

Dome Cameras

QUICK START GUIDE

PLEASE NOTE: 

Complete User Guide, Software, Tools, and Updates are 

available online.  Scan the QR Code or visit:

http://www.vitekcctv.com/Downloads

Summary of Contents for VTD-TND30R3V2









Reviews: