Vitek VT-2299 W, Manual Instructions

Page: 4 / 16

4
ENGLISH
•
Avoid getting of hair into the air inlet grid during
operation of the unit.
•
It is recommended to unwind the power cord to
its full length while using the unit.
• The power cord should not:
–
touch hot objects,
–
run over sharp edges,
–
be used as a handle for carrying the unit.
•
Check the power cord and power plug insulation
integrity periodically.
• Let the unit cool down completely before tak-
ing it away for storage and never wind the power
cord around the unit.
•
Do not attempt to repair the unit. Do not disas-
semble the unit by yourself, if any malfunction is
detected or after it was dropped, unplug the unit
and apply to any authorized service center at the
contact addresses given in the warranty certifi-
cate and on the website www.vitek.ru.
•
To avoid damages, transport the unit in the origi-
nal package only.
•
Keep the unit in a dry cool place out of reach of
children and disabled persons.
THE UNIT IS INTENDED FOR HOUSEHOLD USE
ONLY, ITS COMMERCIAL USAGE AND USAGE
IN PRODUCTION AREAS AND WORK SPACES IS
PROHIBITED.
Using the hairdryer
After unit transportation or storage under cold
(winter) conditions, it is necessary to keep it
for at least 3 hours at room temperature before
switching on.
•
Before switching the unit on, make sure that
your home mains voltage corresponds to the
unit voltage.
• Unwind the power cord completely.
• Insert the power plug into the mains socket.
•
Use the air supply speed switch (6) to set the
required speed, the operation indicator (2) will
light up:
«
0 » – the hairdryer is off
– low speed;
– high speed.
• Set the required air flow temperature using the
switch (5):
– low heating
– medium heating
– maximum heating.
Note: During the first operation some foreign
smell and a small amount of smoke from the
heating element is possible, this is normal.
Hair care
To get the best results, wash your hair with sham-
poo (before drying and styling), dry it with a towel
to remove excessive moisture and comb your hair.
Quick drying
Set the switch (5) to maximal heating position
(position
), select the required air supply speed
using the switch (6) and dry your hair. Shake off
excessive moisture from the hair with your hand or
a comb and constantly move the hairdryer above
your hair.
Straightening
Set the switch (5) to the maximal heating posi-
tion (position
), select the required air supply
speed using the switch (6) and preliminarily dry the
hair. When the hair is almost dry, set the nozzle (1),
reduce the heating degree with the switch (5) and
reduce the air flow speed with the switch (6).
Divide your hair into locks and layers. Start
straightening from the lower layers. Using a plain
or a round comb, brush the hair downwards and
simultaneously direct hot air from the nozzle at
your hair. This way, slowly straighten each lock
from root to end. After you finish straightening the
locks of the lower hair layer, start straightening the
locks of the middle layer and finish with the locks
of the upper hair layer.
Natural wavy hair structure
Set the switch (5) to the low heating position
(position ), select the low air supply speed by
setting the switch (6) to the position
, grip locks
between fingers, turn them in the direction of
natural curling and dry them, directing air between
fingers. When the required effect is achieved, press
the cool shot button (4)
and fix each lock.
Styling
Set the switches (5, 6) to the low heating/speed
position and set the nozzle (1) for directed air flow.
Divide your hair into locks and create a required hair
style by means of a round hair-brush. During hair
styling direct the air flow straight onto your hair in
the desired direction.
If necessary, direct the air flow at each lock for
2-5 seconds to fix hair. Styling time is determined
individually according to hair type.
VT-2299.indd 4 15.01.2018 14:21:18