4
ENGLISH
•
Clean the unit regularly.
•
Do not leave children unattended to prevent
using the unit as a toy.
•
For children safety reasons do not leave
polyethylene bags used as packaging unat-
tended.
Attention! Do not allow children to play with
polyethylene bags or packaging film. Danger of
suffocation!
•
Do not allow children to touch the unit and the
power cord during the unit operation.
•
The unit is not intended for usage by physi-
cally or mentally disabled persons (including
children) or by persons lacking experience or
knowledge if they are not under supervision of
a person who is responsible for their safety or
if they have not been instructed by this person
on the usage of the unit.
•
Do not use the fan if the blades, power cord
or power plug are damaged, if the fan works
improperly, after it was dropped or was dam-
aged in some other way.
•
If the power cord is damaged, it should be
replaced by the manufacturer, a maintenance
service or similar qualified personnel to avoid
danger.
•
Do not attempt to repair the unit. Do not dis-
assemble the unit by yourself, if any malfunc-
tion is detected or after it has fallen, unplug
the unit and apply to any authorized ser-
vice center at the contact addresses given
in the warranty certificate and on the website
www.vitek.ru.
•
Transport the unit in the original package.
•
Keep the unit in a dry cool place out of reach
of children and people with disabilities.
THE UNIT IS INTENDED FOR HOUSEHOLD USE
ONLY, ITS COMMERCIAL USAGE AND USAGE IN
PRODUCTION AREAS AND WORK SPACES ARE
PROHIBITED.
BEFORE THE FIRST USE
After the unit transportation or storage at low
temperature keep it for at least three hours
at room temperature before switching on.
Fan assembling
•
Unpack the fan and remove any advertising
stickers that can prevent its operation.
•
Check the unit for damages, do not use it in
case of damages.
•
Insert the lower part of the bar (13) into the
base (14) and fix it with the clamp (15) by
threading it clockwise. Make sure that the
base (14) is fixed firmly.
•
Unscrew the clamp (12) and extend the bar
(11) to the desired height and fix it by tighten-
ing the clamp (12) with a slight effort as you
turn it clockwise.
•
Install the motor unit (8) on the telescopic
bar (11) until bumping and fix it with the
clamp (10), do not apply excessive effort
when screwing the clamp of the motor
unit (10).
•
Unscrew and remove the rear grid (6) fasten-
ing nut (5).
•
Install the rear grid (6) on the motor unit (8).
The carrying handle on the rear grid (6) should
be turned upwards.
•
Fix the rear grid (6) on the motor unit (8)
with the nut (5) by screwing it clockwise until
bumping.
•
Install the blades (4) on the motor axis (7) and
fix them with the clamp (3), rotating it coun-
terclockwise, holding the blades (4) with a
free hand.
•
Set the nut and the fixing screw into the clamp
ring (2) sockets.
•
Match the front grid (1) and the rear grid (6),
fix them with the clamp ring (2) and tighten
up the clamp ring (2) by turning the fixing
screw tight.
Note! For easy assembling of the fan grids first
install the clamp ring (2) on the rear grid (6) and
tighten it up slightly with the fastening screw.
Install the bottom part of the front grid (1) on
the clamp ring (2). Then press the bottom part
of the front grid (1) to the clamp ring (2) and
squeezing both grids on the both sides install
the grid (1) under the clamp ring (3). Tighten
the fastening screw.
•
The fan is ready for operation.
USAGE
•
Before using the unit for the first time, make
sure that the voltage in your mains corre-
sponds to the unit operating voltage.
IM VT-1928.indd 4
11/20/19 11:47 AM
