ASSEMBLY INSTRUCTIONS
WE RECOMMEND INSTALLATION OF THIS LIGHTING FIXTURE BE DONE BY A
LICENSED ELECTRICIAN.
WARNING *** SWITCH OFF THE MAIN ELECTRICAL SUPPLY FROM THE MAIN
FUSE BOX/CIRCUIT BREAKER BEFORE INSTALLATION.
INSPECT ITEM CAREFULLY BEFORE ATTEMPTING TO INSTALL. IF THERE IS
ANY DAMAGE OR OBVIOUS DEFECT, DO NOT INSTALL.
ITEM MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED.
1.
Carefully remove all parts from the box and remove all plastic covering.
2.
Carefully remove the mounting plate (B) from the back plate (E) by removing
side screws (C).
3.
Drill 4 holes on the wall and make sure the hole distance will match to mounting
plate holes
4.
Knock the plastic anchors (F) into the wall hole
5.
Tight wire rope(T) through hole(W) to screw(S) sand secure tightly screws (K)
6.
Secure the mounting plate (B) to the outlet box in your wall using the two
mounting screws (D) & screws (G)
7.
Attach the ground wire from the fixture to the ground wire from the building
using the provided wire nut (A).
IT IS IMPERATIVE THAT THIS FIXTURE BE GROUNDED
8.
Attach the common wire (neutral white) from the fixture to the white wire from
the building using the provided wire nut (A). Attach the hot wire (lives black)
from the fixture to the black wire from the building with the provided wire nut (A)
Secure each connection by tightening and then checking that no wires can be
pulled out.
9.
Carefully tuck the wires inside the outlet box
10. Secure back plate (E) into mounting plate (B) by side screws(C).
11. Insert bulb (not included) into socket.
12. Put glass shade (J) into fixture (H) and tighten metal ring (J)
13. Installation is complete, turn on power at fuse or circuit breaker
14. This lamp is only installed on smooth wall.
WET
Longacre Small Outdoor Wall Mount
Item # TOBO2120
TOBO2120
ASSEMBLY & INSTALLATION GUIDE
WE RECOMMEND INSTALLATION OF THIS LIGHTING FIXTURE BE DONE BY A LICENSED ELECTRICIAN.
WARNING *** SWITCH OFF THE MAIN ELECTRICAL SUPPLY FROM THE MAIN FUSE BOX/CIRCUIT
BREAKER BEFORE INSTALLATION.
INSPECT ITEM CAREFULLY BEFORE ATTEMPTING TO INSTALL. IF THERE IS ANY DAMAGE OR
OBVIOUS DEFECT, DO NOT INSTALL.
ITEM MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED.
1. Carefully remove all parts from the box and remove all plastic covering.
2. Carefully remove the mounting plate (B) from the back plate (E) by removing side screws (C).
3. Drill 4 holes on the wall and make sure the hole distance will match to mounting plate holes
4. Knock the plastic anchors (F) into the wall hole
5. Tight wire rope(T) through hole(W) to screw(S) sand secure tightly screws (K)
6. Secure the mounting plate (B) to the outlet box in your wall using the two mounting screws (D) & screws (G)
7. Attach the ground wire from the fixture to the ground wire from the building using the provided wire nut (A).
8. IT IS IMPERATIVE THAT THIS FIXTURE BE GROUNDED
9. Attach the common wire (neutral white) from the fixture to the white wire from the building using the provided wire
nut (A). Attach the hot wire (lives black) from the fixture to the black wire from the building with the provided wire nut
(A) Secure each connection by tightening and then checking that no wires can be pulled out.
10. Carefully tuck the wires inside the outlet box
11. Secure back plate (E) into mounting plate (B) by side screws(C).
12. Insert bulb (not included) into socket.
13. Put glass shade (J) into fixture (H) and tighten metal ring (J)
14. Installation is complete, turn on power at fuse or circuit breaker
15. This lamp is only installed on wood wall.
16. Assembly is complete.
17. CARE INSTRUCTIONS:
Wipe all surfaces with a soft dry cloth. Clean glass with a mild soap and water mixture.
Do not use any harsh cleaners (including ammonia-based products) or abrasives, as they will damage the finish.
T
W
GND
