background image

 

 

 

  

 

1.

 

Safety Information  

Warning! This product is not for household use.  

Read this manual before installing and operating the LabSpion, follow the safety 
warnings listed below, and study all the cautions in the manual.  

1.1.

 

Preventing electric shocks 

Make sure the power supply is always grounded. 

Use a source of AC power that complies with the local building and electrical codes, 
that has both overload and ground-fault protection. 

If the controller or the power supply are in any way damaged, defective, wet, or 
show signs of overheating, disconnect the power supply from the AC power and 
contact Viso Service for assistance.  

Do not install or use the device outdoors. Do not spray with or immerse in water or 
any other liquid.  

Do not remove any covers or attempt to repair the controller or the power supply. 
Refer any service to Viso.  

2.

 

Disposing of this Product 

Viso Systems products are supplied in compliance with Directive 2012/19/EU on 
waste - electrical and electronic equipment (WEEE) together with the RoHS Directive 
2011/65/EU with amendments 2015/863. Help preserve the environment! Ensure 
that this product is recycled at the end of its lifetime. Your supplier can give details of 
local arrangements for the disposal of Viso Systems products.  

3.

 

Introduction 

About the LightSpion Extender 

The LightSpion Extender expands the ability of LightSpion to measure the light 
sources with a diameter of up to 220mm. The device is easily connected to the 
previously installed LightSpion and gets detected by the Light Inspector software 
automatically. 

About this document 

These guidelines describe the installation process of the LightSpion Extender and the 
alignment of light sources to be measured. 

© 2007 Viso Systems ApS, Denmark 

All rights reserved. No part of this manual may be reproduced, in any form or by any means, 
without permission in writing from Viso Systems ApS, Denmark. Information subject to change 
without notice. Viso Systems ApS and all affiliated companies disclaim liability for any injury, 
damage, direct or indirect loss, consequential or economic loss or any other loss occasioned by 
the use of, inability to use or reliance on the information contained in this manual. 

Summary of Contents for LightSpion



















Reviews: