manualshive.com logo in svg

Vislink IRD6200, User Manual

Share
Download
Vislink IRD6200 User Manual Download Page 20

 

IRD6200 IRD User Manual 

 

Main Display 

 

 
Issue No: 1 

Page: 14 

 
Ref: IRD6-ASUM-700X 

 

Copyright © 2019 Vislink Technologies, Inc. 

4.3.

 

Unit Setup Menu 

4.3.1.

 

Presets 

The unit allows you to save up to 16 preset configurations. There is also 
functionality to dump the unit’s current configuration to a USB memory stick. We 
may require you to email the configuration.txt file to customer support, to assist 
with any problems. 

NOTE: Performing a Restore Defaults will clear all stored Presets. 

Function 

Description 

Save to 

Memory 

Specify the number of the preset to be saved. It is possible to enter a name 
for the preset if desired. Change SAVE to YES and press ENTER to save the 
preset. 

Recall from 

Memory 

Specify the number of the preset to recall; if a name has been assigned this 
will be displayed. Change RECALL to YES and press ENTER to load the 
preset. 

Table 4-2 

Presets Menu Overview 

4.3.2.

 

Control Interface 

Configure external control interfaces. 

Function 

Description 

Web Identifier 

Set a text string to display on the unit’s web page. This helps to identify the 
unit in use when working with multiple units. 

Ethernet Port 

Set the IP parameters for the Ethernet control port. 

Status Pin 

The Status pin in the CC/ALM connector (see Section 2.13.8) is an open-drain 
output that connects to Ground when active. When active, the default value 
is to active an Alarm. You can choose whether it is active high or low. It can 
also be driven manually using this menu. 

Table 4-3 

Control Interface Menu Overview 

4.3.2.1.

 

SNMP 

The SNMP menu enables you to configure SNMP (Simple Network Management 
Protocol) options. SNMP allows you to control and monitor the system using MIBs 
(Management Information Base) and capture unsolicited alarms (Traps). MIBs are 
available via the web interface. 

4.3.3.

 

Defaults 

Restore the unit default values or perform a reboot. 

Function 

Description 

Defaults 

To restore the unit to factory defaults, change RESTORE DEFAULTS to YES 
and press ENTER. 

Reset 

To reset the unit, select Yes and press ENTER. 

Reboot 

To reboot the unit, select Yes and press ENTER. 

Table 4-4 

Defaults Menu Overview 

4.3.4.

 

Licenses 

Enter license codes and display which features you have licensed in the unit. See 
Section 5.1 for more details. 

Summary of Contents for IRD6200

























Reviews:

No comments

Brands by name

Popular brands

Load more brands