Vislink ADVENT DCU5000 Operation Handbook Download Page 10

Page: 10 / 42

Advent Communications

209297 – DCU5000 Drive Control Unit

Page 10 of 42

3.3. SENSORS

This interface is designed to interface with any position, limit switches or sensors fitted
to the antenna.

Detailed descriptions are beyond the scope of this manual. Contact Advent
Communications for further guidance and information.

Connector: 25-pin male D-type.

Pin Number Sensor Signal

description

Sensor 1

+12V DC supply.

2 Signal

input.

14 GND

Sensor 2

+12V DC supply.

15 Signal

input.

16 GND

Sensor 3

+12V DC supply.

5 Signal

input.

17 GND

Sensor 4

+12V DC supply.

18 Signal

input.

19 GND

Sensor 5

+12V DC supply.

8 Signal

input.

20 GND

Sensor 6

+12V DC supply.

21 Signal

input.

22 GND

12 TX

Position

micro-switch

13 NC
25 Common
24 Stow

Position

micro-switch

23 NC
11 Common

Summary of Contents for ADVENT DCU5000











































Search results

Summary of Contents for ADVENT DCU5000

Reviews:

Related manuals for ADVENT DCU5000

Brands by name

Popular brands

Vislink ADVENT DCU5000, Operation Handbook

Search results

Summary of Contents for ADVENT DCU5000

Reviews:

Related manuals for ADVENT DCU5000

Brands by name

Popular brands