Introduction
Thanks for choosing the Vision’s repeater of the home automation device. This module is a
Z-
Wave™ enabled device (interoperable, two-way RF mesh networking technology) and is
fully compatible with any Z-
Wave™ enabled network. Every main powered Z-Wave
enabled device acts as a signal repeater and multiple devices result in more possible
transmission routes which helps
eliminate “RF dead-sports”
Z-
Wave™ enabled devices displaying the Z-Wave™ logo can also be used with it
regardless of the manufacturer, and ours can also be used in other manufacturer’s
Z-
Wave™ enabled networks. This device take existing Z-WAVE signal, repeat and send it
to a longer range where it is too far away for the controller (supporting FLiRS devices).
Product Description and Specification
*** For indoor use only ***
Specification:
Package Content:
Protocol: Z-Wave
™ (ZM4102)
Frequency Range:
865.22MHz (ZR1202IN-5)
868.10MHz (ZR1202MY-5)
868.42MHz (ZR1202EU-5)
869.00MHz (ZR1202RU-5)
908.42MHz (ZR1202US-5)
916.00MHz (ZR1202IL-5)
979.70MHz (ZR1202KR-5)
919.80MHz (ZR1202HK-5)
920-928MHz(ZR1202JP-5)
921.42MHz (ZR1202BR-5)
Operating Range: Up to 200 meters
Operating Temp.: -15
°
C~ 60
°
C (5
°
F ~140
°
F)
Operating Voltage: 5V/DC
Current Consumption: 300mA (
±
50mA)
1pc
1pc
1pc
1pc
ZR1202 Repeater module
ZR1202 Repeater Bracket
Adapter (Optional)
Installation & Operation Manual
Z-
Wave™ Command Class:
COMMAND_CLASS_ASSOCIATION_GRP_INFO
COMMAND_CLASS_ASSOCIATION_V2
COMMAND_CLASS_DEVICE_RESET_LOCALLY
COMMAND_CLASS_FIRMWARE_UPDATE_MD_V2
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2
COMMAND_CLASS_POWERLEVEL
COMMAND_CLASS_VERSION_V2
COMMAND_CLASS_ZWAVEPLUS_INFO
※
Note: Suitable adapter specification:
-Micro USB Power Input
-Operating Voltage: 5V/DC
-Current Consumption: 500mA
Installation
Notice: If you are installing the entire Z-
Wave™ system for the first time, please refer to the installation
guide of Z-
Wave™ Interface Controller before installing ZR 1202 Repeater Module.
1.
Fix the repeater under the vertical way as high as possible then insert the suitable
Micro USB
Power Adaptor
to the ZR1202 then it will go to the Learning Mode automatically. (The LED will
start flash which means the repeater has not been
“Include” yet.)
2.
For “
Inclusion
” in (adding to) a network: Put the Z-Wave™ Interface Controller into
“
inclus
ion”
mode and following its instruction to add the ZR1202 to your controller. To get into
the “inclusion”
mode, the distance between module and controller is suggested to be in one meter. Press the
program switch on the ZR1202 three times in 3 seconds. The LED should stop flashing, if not,
please try again.
For “
Exclusion
” from (removing from) a network: Put the Z-Wave™ Interface Controller into
“exclusion” mode, and following its instruction to delete the ZR1202 from your controller. Press
the program switch on the ZR1202 three times in 3 seconds to be excluded.
Note: LED setting light will flash continuously in Exclusion condition.
For
“Association”
: Support one association group (5 nodes).
3.
Use
“Power Level Set” command for setting the strength of RF during one period.
4.
Use
“Power Level Test Node Set” command to test the direct signal for fixed node.
5.
Support Repeaters for routing (FLiRS included)
6.
Support Explorer Frame function
7.
Press Program Switch for 5 seconds, the ZR1202 will reset back to factory default. (Remark: This
is to be used only in the case of primary controller being inoperable or otherwise unavailable.)
8.
Support OTA Firmware update from controller. Please refer to your controller manual. Once
OTA function success, please make sure to exclusive the device & inclusive again before use the
device.
5. Security enabled_ Z-Wave controller must be used to fully utilize the product.
6. Lifeline group used command :
{COMMAND_CLASS_DEVICE_RESET_LOCALLY,DEVICE_RESET_LOCALLY_NOTIFICATION}
★
The ZR1202 operating range will be up to 200 meters open site under the
correct installation!!
(2)
(1)
Micro USB Power Input
Program Switch
Release the bracket:
(1) Press
(2) Slide down to release the bracket
-1-
-2-
