background image

Operation

   

 

1. 

Opening/Closing the door/window to separate the magnet from the sensor will send 
signal to any association nodes accordding to the Status/Signal table on page 2 and 
the LED will flash once. 

2. 

Normal operation, the LED will not light.   

3. 

If the cover of sensor is removed, the tamper switch will send signal according the 
Status/Signal table, and the LED will go solid and ZD2105 will send 

“Wake Up 

Notification

”. ZD2105 will go to sleep mode and the red LED will go off after 10 

seconds. 

4. 

ZD2105 will send signal according the status / signal table after closing the cover 
back 2 seconds. 

 

 

Federal Communications Commission Statement 

This equipment has been followed to comply with Part 15 of the FCC Rules. This 
equipment generates, uses and can radiate radio frequency energy and, if not installed 
and used in accordance with the instruction, may cause harmful interference to radio 
communications. However, there is no guarantee that interference will not occur in a 
particular installation. If this equipment does cause harmful interference to radio or 
television reception, which can be determined by turning the equipment off and on, the 
user is encouraged to try and correct the interference by one of the following measures: 
-Reorient or relocate the receiving antenna, 
-Increase the separation between the equipment and receiver, 
-Connect the equipment into and outlet on a circuit different from that to which the 
receiver is connected. 
Consult the dealer or an experienced radio/TV technician for help. 
This device complies with Part 15 of the FCC Rules. Operation is subject to the following 
two conditions: (1) this device may not cause harmful interference, and (2) this device 
must accept any interference received, including interference that may cause undesirable 
operation. 
FCC Caution: Any changes or modifications not expressly approved by the party 
responsible for compliance could void the user’s authority to operate this equipment. 

Limited Warranty 

Vision Guarantees that every wireless door/window sensor is free from physical defects in 
material and workmanship under normal use for one year from the date of purchase. If 
the product proves defective during this one-year warranty period, Vision will replace it 
free of charge. Vision does not issue any refunds. This warranty is extended to the 
original end user purchase only and is not transferable. This warranty does not apply to: 
(1) damage to units caused by accident, dropping or abuse in handling, or any negligent 
use; (2) units which have been subject to unauthorized repair, taken apart, or otherwise 
modified; (3) units not used in accordance with instruction; (4) damages exceeding the 
cost of the product; (5) transit damage, initial installation costs, removal cost, or 
reinstallation cost. For information on addtional devices, please visit us at 

www.visionsecurity.com.tw 

 

 

 

 

 

 

Installation & Operation Manual 

 

ZD2105IN-5 

ZD2105MY-5 

ZD2105EU-5 

ZD2105RU-5 

ZD2105US-5 

ZD2105IL-5 

ZD2105KR-5 

ZD2105HK-5 

ZD2105JP-5 

ZD2105BR-5 

 

Recessed Door/ Window Sensor 

 
 
 
 

                                             

 

ZD 2105-5  V0  1070126   

Summary of Contents for ZD2105IN-5

Page 1: ... which the receiver is connected Consult the dealer or an experienced radio TV technician for help This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesirable operation FCC Caution Any changes or modif...

Page 2: ...9 923MHz ZD2105KR 5 919 80MHz ZD2105HK 5 922 926MHz ZD2105JP 5 921 42MHz ZD2105BR 5 Operating Range Up to 100 feet line of sight Operating Temp 15 C 60 C 5 F 140 F Battery CR2 1PC 1pc 1pc 1pc 1pc 2pcs 1pc ZD 2105 5 sensor Magnet CR2 Lithium Battery Accessary pack Screws for bracket sensor Installation Operation manual Z Wave Command Classes COMMAND_CLASS_ASSOCIATION_GRP_INFO COMMAND_CLASS_ASSOCIAT...

Page 3: ...he program switch the red LED will flash slowly if the ZD2105 has not been included yet After power on the red LED will go on if the ZD2105 has been included The LED will turn on till the rear cover has been closed with the front cover firmly the LED should go off 5 For Inclusion in adding to a network Put the Z Wave Interface Controller into inclusion mode and following its instruction to add the...

Page 4: ...able 15 Support OTA Firmware update from controller Please refer to your controller manual Once OTA function success we recommend you exclusive the device inclusive again before use the device 16 Support SECURITY S0 SECURITY S2 UNAUTHENTICATED SECURITY S2 AUTHENTICATED 17 Support SmartStart please scan the QR Code from ZD2105 for SmartStart QR code and PIN is located on the device also there is a ...

Reviews: