background image

15 

TC2-CTL3_manual_en 

SPECIFICATIONS 

PRODUCT DIMENSIONS: 71 x 42 x 31mm (length x width x height) 
PRODUCT WEIGHT: 63 grams 

CONSTRUCTION MATERIAL: Plastic 

COLOUR: White 
POWER SUPPLY: 100-240v AC 50/60Hz 12 volt / 0.5 amp 

Transformer integrated into plug. Includes interchangeable plugs: UK/EU/US/AU. DC tail length: 
4m. Transformer dimensions: 66 x 43 x 30mm 

POWER CONSUMPTION 
Static: <= 5uA 

Sending: <= 20mA 
Copying: <= 10Ma 

COMPLIANCE: RoHS, WEEE & CE Compliant 

 

ACCESSORIES INCLUDED 

5 x Blanking buttons 

1 x Labels 
1 x Single-Gang Techconnect Backbox 

1 x Single-Gang Techconnect Surround 

1 x IR Blaster with 150mm cable (terminated with female minijack) 
1 x IR Blaster with 10m cable 

 
WARRANTY 

This product comes with a 2-year return to base warranty, effective from the date of purchase. 
This warranty applies only to the original purchaser and is not transferable. For the avoidance of 

doubt, this will be taken from the information held by the appointed national distributor at the 
point of sale. If the product is DOA (dead on arrival), you have 21 days from purchase date to 

notify the national distributor via your AV reseller. The liability of the manufacturer and its 
appointed service company is limited to the cost of repair and/or replacement of the faulty unit 

under warranty, except for death or injury (EU85/374/EEC). This warranty protects you against 
the following: 

• Failure of any components, including the power supply. 
• Damage when the product is first removed from its packaging if reported within 24 hours of 

purchase. 
If you find you do have a problem with this product, you should contact the AV reseller you 

purchased this product from. The original purchaser is responsible for shipment of the product 

to the manufacturer’s appointed service centre for repair. 
We will endeavour to return repaired units within 5 working days, however this may not always 

be possible, in which case it will be returned as soon as practicably possible. In line with our 
WEEE commitments, the manufacturer endeavours to replace the faulty parts of the product 

rather than replacing the whole unit. This warranty does not protect this product against faults 
caused by abuse, misuse, incorrect installation, unstable or faulty power input, which might be 

caused by ignoring the guidelines set out in this manual. 
 

LEGAL DISCLAIMER: Because we are committed to improving our products, the details above 

may change without prior warning. This User Manual is published without warranty and any 

improvements or changes to the User Manual necessitated by typographical errors, inaccuracies 

of current information, or improvements to programs and/or equipment, may be made at any 

time and without notice. Such changes will be incorporated into new editions of the User 

Manual. 

Summary of Contents for techconnect control 3
















Reviews: