SET-UP
Step 1: QuickCart Assembly
STEP 1b
1a
Turn the cart upside down and remove the nuts and washers from the bolts
welded on the cart carefully.
1b
Pull both ends of the QuickCart open in the direction indicated by the arrows and
align the screws with the screw holes.
1c
There are four (4) screws (2 on upper and 2 on lower layers) to complete
assembly. Firstly, install the flat washer, then the spring lock washer, and finally,
the lock the nut with the provided wrench.
1d
Screw in Standard Rubber Wheels to rear Cart Legs and the Locking Rubber
Wheels to the front Cart Legs.
• After cart is assembled, confirm all bolts are tightened.
• Close lid and press top vent onto grill with calibrations facing the front.
ATTENTION!
THE AIR LIFT HINGE WILL CAUSE THE TOP LID TO JUMP SLIGHTLY WHEN
PULLING ON THE LATCH BUTTON.
STEP 1a
STEP 1c
STEP 1d
STEP 5
Step 3: Handle and Side Shelf Mounting
• Remove nuts and washers from bolts welded
on the top banding opposite the hinge.
• Remove paper washers and attach handle
bracket over studs. On each stud place a flat
washer and an acorn nut, then tighten.
• Mount side shelves by inserting the shelf
rod into the shelf bracket. Tilting the shelf
up slightly and sliding in or out allows you to
deploy or store the shelves.
Step 8: KamadoMatic™ Hinge Adjusting
• Once grill is cool, it is safe to remove ash from
ash drawer.
• Using bottom knob on Ash Drawer, lift slightly
(Step 7a) and pull drawer out (Step 7b).
• Once ash is emptied, reinstall by pushing Ash
Drawer back into grill body until it drops down
back into place.
WARNING:
ALWAYS WAIT FOR ASH TO COOL
BEFORE REMOVING ASH DRAWER. NEVER PULL
OUT ASH DRAWER WHILE GRILL IS HOT.
• Open grill and take off grill grates to
expose fire bowl.
• Spread bracket so it makes an “X” shape
and lower onto fire bowl, allowing the
bracket to rest on edge of bowl.
• Lower Lava Stone onto the bracket.
Step 5: Grill Assembly
0 1 2
3
STEP 7a
STEP 7b
Step 4: Shelf Brackets
Step 2: Top Vent Assembly
ÉTAPE 2
STEP 4
• Remove the nuts and washers from the
bolts welded on the bottom banding
carefully.
Remove the paper washers.
• Place the side brackets on the bolts and
screw side brackets down tightly with the
nuts and washers. Mount shelf brackets
over studs on the sides of the metal
bands on the bottom ceramic grill body
with bracket slots facing up. Brackets
are stamped on the back with letters
indicating their position (e.g., LF=Left
Front bracket and RB=Right Back bracket).
• Mount a flat washer then acorn nut on each stud and tighten with provided wrench.
HASTY REMOVAL
CAN RESULT IN
DAMAGE TO GRILL.
STEP 2
STEP 3
• Take all parts out of grill before lifting. The
grill is heavy and will require two people to
lift and guide the Kamado into cart.
• Be sure the Ash Drawer is centered between
the two front legs and the grill is resting
against the two back legs.
• Lower fire bowl into grill with the ash drawer
opening lined up with the opening in the
main ceramic body. Place cast iron charcoal
grate with attached starter pocket into fire
bowl
(Step 5)
. Align tabs of starter pocket
with electric starter port in fire bowl.
• Place cooking grates onto grill with hinged
section facing towards front of grill.
STEP 8
WARNING:
PERFORMING MANUAL
ADJUSTMENTS TO THE HINGE CAN
CAUSE UNEXPECTED MALFUNCTION
OR DAMAGE IF THESE STEPS ARE
NOT FOLLOWED CORRECTLY.
STEP 6
Step 6: Lava Stone &
Bracket Assembly
Step 7: Ash Drawer Usage
1. When moving your grill please remember to make sure locking casters are
in the unlocked position and always pull your grill. Never Push it. Pull from
the Back Hinge. Not the Handle. Your grill is more likely to tip if you push it
and it hits a bump or indention on the ground.
2. Do not remove your Fire Bowl. Clean ash by brushing excess ash into ash
drawer and removing. The purpose of the Fire Bowl is to hold your lump
charcoal and will continue to work even if it is cracked.
Long-Term Maintenance
The KamadoMatic™ Hinge on your Pro
Kamado is already pre-adjusted for
ideal balance and stability. Follow these
instructions to manually adjust the hinge
further to your preference.
CAUTION:
KamadoMatic™ Hinge under
high tension.
• Open the dome of your Pro Kamado.
• While holding the top dome open with
one hand, use the provided 13mm
wrench to adjust the Spring Nut as
shown in
Step 8 illustration
.
• If the top dome jumps up too quickly
upon opening, turn the Spring Nut
Counter Clockwise
to loosen the spring and reduce tension. Turn the Spring Nut
for two turns at a time and test the lid for your preference. The Spring Nut can
also be turned
Clockwise
to tighten the spring and add tension, if necessary.
NOTE:
Depending on the amount of resistance and tightness of seal it may be
necessary to use a small amount of force to lock the lid and have the lock handle
slide into the latch. Be careful not to slam the top lid shut.
