Vishay TSSP57038H Manual Download Page 8

TSSP57038H

www.vishay.com

Vishay Semiconductors

  

 

Rev. 1.3, 10-Apr-2019

8

Document Number: 82798

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT 

www.vishay.com/doc?91000

LABEL

Standard bar code labels for finished goods

The standard bar code labels are product labels and used

 

for identification of goods. The finished goods are packed in

 

final packing area. The standard packing units are labeled

 

with standard bar code labels before transported as finished

 

goods to warehouses. The labels are on each packing unit 
and contain Vishay Semiconductor GmbH specific data.

DRY PACKING

The reel is packed in an anti-humidity bag to protect the

 

devices from absorbing moisture during transportation and

 

storage.

FINAL PACKING

The sealed reel is packed into a cardboard box.

 

 

 

RECOMMENDED METHOD OF STORAGE

Dry box storage is recommended as soon as the aluminum

 

bag has been opened to prevent moisture absorption. The

 

following conditions should be observed, if dry boxes are

 

not available:

• Storage temperature 10 °C to 30 °C

• Storage humidity 

 60 % RH max.

After more than 168 h under these conditions moisture

 

content will be too high for reflow soldering.

In case of moisture absorption, the devices will recover to

 

the former condition by drying under the following condition:

192 h at 40 °C + 5 °C / - 0 °C and < 5 % RH (dry air / 
nitrogen) or 

 

96 h at 60 °C + 5 °C and < 5 % RH for all device containers

 

or 

 

24 h at 125 °C + 5 °C not suitable for reel or tubes.

An EIA JEDEC

®

 standard J-STD-020 level 3 label is included

 

on all dry bags.

VISHAY SEMICONDUCTOR GmbH STANDARD BAR CODE PRODUCT LABEL

 (finished goods)

PLAIN WRITING

ABBREVIATION

LENGTH

Item-description

-

18

Item-n

u

mber

INO

8

Selection-code

SEL

3

LOT-/serial-n

u

mber

BATCH

10

Data-code

COD

3 (YWW)

Plant-code

PTC

2

Q

u

antity

QTY

8

Accepted by

ACC

-

Packed by

PCK

-

Mixed code indicator

MIXED CODE

-

Origin

Company logo

Long bar code top

Type

Length

Item-n

u

mber

N

8

Plant-code

N

2

Se

qu

ence-n

u

mber

X

3

Q

u

antity

N

8

Total length

-

21

Short bar code bottom

Type

Length

Selection-code

X

3

Data-code

N

3

Batch-n

u

mber

X

10

Filter

-

1

Total length

-

17

Aluminum bag

Label

Reel

15973

Summary of Contents for TSSP57038H











Reviews: