22
included as standard delivery.
*Not included
4. STANDARD EQUIPMENT
- Router/Trimmer FRB300
– Dust knob
– Guide with roller
– Parallel guide
– Service key e/c:22
– Collets of 6 and 8 mm
– Operating instructions
– Warranty document
5. SPECIFICATIONS OF THE TOOL
Brushless motor
Power tool equipped with a brushless motor that provides
the following advantages (compared to the power tool
having a brush motor):
• High reliability due to the lack of wearing parts (carbon
brushes, commutator);
• Increased operating time on a single charge.
Temperature protection
The temperature protection system enables to automa-
tically deactivate the power tool in case of excess load
or when the temperature of the battery 8 is exceeding
70°C. The system guarantees protection of the power
tool from damage in case of noncompliance with the
operation conditions.
Overdischarge protection
The battery 8 is protected by the safety system against
deep discharge. In case of complete discharge, the power
tool is automatically switched off.
Do not try to switch on the power tool
when the protection system is activated
the battery 8 can be damaged.
Indicators of the state of battery charge
With the push of the button 10 the indicators 11 show
the state of charge of the battery 8.
Overheating protection
Overheating protection system of the engine automati-
cally switches off the power tool in case of overheating.
In this situation, let the tool cool before turning the
power tool on again.
Overload protection
Overload protection system of the engine automatically
switches off the power tool when it is operated in a
manner that causes it to draw an abnormally high current.
Soft start
Soft start enables smooth start of power tools - the
spindle is being run up gradually with no jerks and
kickbacks; no jump-like load is imposed on the motor
upon switching.
LED lamp
When stand-by mode is switched on (as described
above), the LED lamp 12 lit this improves the visibility
of the treatment area.
Rotation speed stabilization system
The stabilization system maintains the preset RPM both
at an idle speed and under load. This allows for the
smooth advance of the power tool during operation.
Speed selector thumbwheel
Using speed selector thumbwheel 13, you may select the
required spindle speed (also during operation).
The required speed is dependent on the material and
can be determined with practical trials.
When operating your power tool at a low speed for a
long time, it has to be cooled down for 3 minutes. To
do it, set a maximum speed and leave your power tool
to run idle.
6. CHARGING PROCEDURE OF THE POWER TOOL
BATTERY
Initial operating of the power tool
Before the first use, the battery 8 must be fully charged.
Charging process (see Fig. 8)
• Press the battery lock 9 and remove the battery 8
(see Fig. 8.1).
• Connect the charger 24 to the power supply.
• Insert battery 8 into charger 24 (see Fig. 8.2).
• Disconnect the charger 24 from power supply after
charging.
• Remove the battery 8 from the charger 24 and mount
battery 8 in the power tool (see Fig. 8.3).
Charger indicators (see Fig. 8)
Charger indicators 36 and 37 inform of the battery 8
charging process. Signals of the indicators 36 and 37
are shown on the label 38 (see Fig. 8).
• Fig. 8.4 - (The green indicator 36 is on, the battery 8
is not inserted in the charger 24) - the charger 24 is
connected to the power network (ready for charging).
• Fig. 8.5 - (The green indicator 36 is blinking, the battery
8 is inserted in the charger 24) - the battery 8 is being
charged.
• Fig. 8.6 - (The green indicator 36 is on, the battery 8
is inserted in the charger 24) - the battery 8 is fully
charged.
• Fig. 8.7 - (The red indicator 37 is on, the battery 8 is
Summary of Contents for FRB300
