background image

19

One-Year Limited Warranty for Lamps, Sleeves and UV Sensors 

VIQUA warrants lamps, sleeves and UV sensors to be free from defects in material 

and workmanship for a period of one (1) year from the date of purchase. During this 

time, VIQUA will repair or replace, at its option, any defective parts covered by the 

warranty.Your dealer will process your claim and advise  whether the defective item 

needs to be returned for failure analysis. 

IMPORTANT NOTE: Use only genuine Sterilight

®

 replacement lamps and 

sleeves in your system. Failure to do so may seriously compromise disinfection 
performance and affect warranty coverage.

    

General Conditions and Limitations

 

None of the above warranties cover damage caused by improper use or maintenance, 

accidents, acts of God or minor scratches or imperfections that do not materially 

impair the operation of the product. The warranties also do not cover products that 

are not installed as outlined in the applicable Owner’s Manual. 

Parts repaired or replaced under these warranties will be covered under warranty 

up to the end of the warranty period applicable to the original part. 

The above warranties do not include the cost of shipping and handling of 

returned items

The limited warranties described above are the only warranties applicable to the 

Sterilight

®

 range of products. These limited warranties outline the exclusive remedy 

for all claims based on a failure of or defect in any of these products, whether the 

claim is based on contract, tort (including negligence), strict liability or otherwise. 

These warranties are in lieu of all other warranties whether written, oral, implied 

or statutory. Without limitation, no warranty of merchantability or of fitness for a 

particular purpose shall apply to any of these products. 

VIQUA does not assume any liability for personal injury or property damage caused 

by the use or misuse of any of the above products. VIQUA shall not in any event be 

liable for special, incidental, indirect or consequential damages. VIQUA’s liability shall, 

in all instances, be limited to repair or replacement of the defective product or part 

and this liability will terminate upon expiration of the applicable warranty period. 

Summary of Contents for SHF-140

























Reviews:

Related manuals for SHF-140