Viper Viper 125HF Owner'S Manual Download Page 9

6

©

1999 Directed Electronics, Inc.

Using Your System 

The following safety warnings must be observed at all times:

Due to the complexity of this system, installation of this

product must only be performed by an authorized DEI dealer.

When properly installed, this system can start the vehicle via

a command signal from the remote control transmitter.

Therefore, never operate the system in an enclosed area or

partially enclosed area without ventilation (such as a garage).

When parking in an enclosed or partially enclosed area or

when having the vehicle serviced, the remote start system

must be disabled using the installed toggle switch. It is the

user's sole responsibility to properly handle and keep out of

reach from children all remote control transmitters to assure

that the system does not unintentionally remote start the

vehicle. 

THE USER MUST INSTALL A CARBON MONOXIDE

DETECTOR IN OR ABOUT THE LIVING AREA ADJACENT TO THE

VEHICLE. ALL DOORS LEADING FROM ADJACENT LIVING

AREAS TO THE ENCLOSED OR PARTIALLY ENCLOSED VEHICLE

STORAGE AREA MUST AT ALL TIMES REMAIN CLOSED.

These

precautions are the sole responsibility of the user.

Use of this product in a manner contrary to its intended mode

of operation may result in property damage, personal injury,

Warning! Safety First

Summary of Contents for Viper 125HF



















Reviews: