background image

22

© 2016 Directed. All rights reserved.

cally start the engine to maintain battery charge or combat extreme 
cold when parked for an extended period of time. 
 

Precautions for the Advanced Start features: 

• 

Park

 the vehicle in a well ventilated area away from windows 

and doors that lead into inhabited spaces.

• 

Arm/Lock

 the vehicle, the engine will not start unless the system 

is armed.

•  Only one Advanced start feature can be enabled at any given 

time.

•  For manual transmission vehicles, MTS Mode must be enabled 

before Timer Start or Smart Start can be activated.

•  Timer Start or Smart Start Mode automatically exits when the 

vehicle is disarmed.

Timer Start operation

 

Activation begins a countdown timer as set by the installer (de-
fault three hours). When the timer expires the engine starts. When 
the Remote start runtime expires the engine shuts off, and the 
countdown timer restarts. This will repeat as many times as set 
by the installer (default is six starts). Timer Start is exited after the 
final start.

 

Smart Start operation 

Smart Start uses the settings for Timer Start in addition to tempera-
ture and battery level to automatically start the engine. Activation 
begins the countdown timer. When the timer expires the vehicle 
interior temperature and battery level is checked and, if the Tem-
perature is above 100°F, below 0°F, or  the battery level is be-
low 10.5V, the engine will start. When the Remote Start runtime 
expires, the engine shuts off, and the countdown timer restarts. 
Smart Start is exited after the final start.

Summary of Contents for 5606V











































Reviews: