manualshive.com logo in svg

Vinten Protouch PRO-6 HDV, Operator'S Manual

Share
Download
Vinten Protouch PRO-6 HDV Operator'S Manual Download Page 23

Back

23

Battery replacement 

The battery illuminates the level bubble 

(11)

 when the switch 

(13)

 is pressed. The level bubble 

remains lit for approximately 15 seconds, or until the switch 

(13)

 is pressed a second time.

The battery should be replaced yearly or when the switch 

(13)

 illuminates red to warn of a low bat-

tery level.

To replace the battery 

(Fig 7)

:

Apply the pan brake 

(15)

 and remove the illumination module 

(12)

 by pressing the retaining 

tabs 

(12.1)

 together from the underside of the head. The illumination module will then lift 

out of the head.

Push the battery 

(12.2)

 out of the illumination module from behind using a suitable pointer 

(pen).

Push the replacement battery into the illumination module, observing the correct polarity.

Refit the illumination module 

(12)

 into the head. Push downward until in ‘snaps’ into place.

Press the switch 

(13)

 and ensure that the level bubble 

(11)

 is lit for approximately 15 sec-

onds.

Fig 7  Battery replacement

(12)

(12.1)

(12.2)

(15)

(11)

(13)

BATTERY TYPE

3v, CR1220

Summary of Contents for Protouch PRO-6 HDV






























Reviews:

No comments

Brands by name

Popular brands

Load more brands