TROUBLESHOOTING
OPERATION ANOMALIES
Ensure that there is power to the electrical supply plug
by connecting another electrical appliance to it. Check
fuse, if any. Make sure that the door is closed properly.
If your Wine Cellar and Beverage Centre appears to be
malfunctioning, unplug it and contact your VINTEC’s after
sales service. Any intervention on the cold circuit should
be performed by a refrigeration technician who should
carry out an inspection of the circuit sealing system.
Similarly, any intervention on the electrical circuit
shouldbe performed by a qualified electrician.
Notes : Any intervention performed by a non- authorised
technician by Vintec will lead to the warranty being
considered as null and void.
POWER FAILURES
In the event of a power interruption, all previous
temperature settings are automatically erased and it
will revert to a preset temperature setting. (See preset
chart). Most power failures are corrected within a short
period of time. An hour or two’s loss of power will not
affect Wine Cellar and Beverage Centre’s temperatures.
To avoid sudden change of temperature while the
power is off, you should avoid opening the door.
For longer periods of power failure, do take steps
to protect your wine.
Irrespective of the cause, if you notice either abnormal
temperature or humidity levels inside your Wine Cellar
and Beverage Centre, be reassured that only long and
frequent exposure to these abnormal conditions can
cause a detrimental effect on your wines.
TROUBLESHOOTING GUIDE
Common problems may easily be solved,
saving you the cost of a possible service call.
Please read carefully the instruction manual
and refer to the troubleshooting guide chart.
PROBLEM
POSSIBLE CAUSE
Wine Cellar and Beverage
Centre does not operate.
Wine Cellar and Beverage
Centre is not cold enough.
Turns on and off frequently.
The light does not work.
The Wine Cellar and Beverage
Centre seems to make too
much noise.
Not plugged in.
The appliance is turned off.
The circuit breaker tripped or the fuse is
broken.
Check the temperature control setting.
External environment may require a
higher setting.
The door is opened too often.
The door is not closed completely.
The door gasket does not seal properly.
The room temperature is higher than
normal.
A large amount of contents has been
added to the Wine Cellar and Beverage
Centre.
The door is opened too often.
The door is not closed completely.
The temperature control is not set
correctly.
The door gasket does not seal properly.
Not plugged in.
The circuit breaker tripped or a blown
fuse.
The bulb is out of order.
The light button is “OFF”.
Check to assure that the Wine Cellar and
Beverage Centre is level.
A Gurgling noise may come from the low
side of the refrigerant system, which is
normal as each cycle ends in your Wine
Cellar and Beverage Centre.
Contraction and expansion of the inside
walls may cause popping and crackling
noises.
The Wine Cellar and Beverage Centre is
not level.
Vibrations.
The door will not close properly.
The Wine Cellar and Beverage Centre is
not level.
The door was reversed and not properly
installed.
The gasket is faulty. (Magnet or rubber
is spoiled).
The shelves are out of position.
9
User Manual
1. Open the door to a 90 degrees angle, take out the 2
screws from lower door axis, remove the door ,
Remove the axis plate from the door. Unscrew the
screw located underneath the doorframe and the
limit device , and relocate it at left end side of the
door frame.
2. Take out the 3 hinge screws from the lower hinge
(right) and remove it.
3. Take out the 3 hinge screws from the top hinge
(right) and remove it.
4. Remove decorative nail from left top of cabinet
and install spare top hinge (Left) at left top of
cabinet with 3 screws.
5. Following the above procedure, install the spare
lower hinge to the left.
6. Install and aligned the door.
7. Insert the plastic caps to cover the holes.
