background image

                                                                 

 

                            

 

- 21 -

f.  Refrigerant low or leaking 
 
g.  Capillary tube blockage 

f.  Check for current and sealed 

system leakage 

g.  Check for low side pressure  

11.Water leak

 

a. High humidity 
b.  Air leak in wine cellar 
c.  Evaporator air flow restriction 
 
d. Water passages restricted 
e.  Drip tray leak 

a.  Use drain line  
b.  Check for any air leak 
c. Check air flow or air TD crossing 

evaporator  

d.  Clean the drip tray 
e.  No water overflow but leak 

12.Circuit 

tripping

 

a.  Incorrect fuse or breaker 
b. Incorrect 

wirings 

c. Failed 

components 

 

a.  Check for proper fuse or breaker 
b.  Check for wirings and connections 
c.  Call service  
 

13.Noisy 

operation

 

a.  Mounting area not firm 
b. Loose 

parts 

 
 
c.  Compressor overloaded due to 

high ambient temperatures or 
airflow restriction 

d. Malfunctioning 

components 

 

a.  Add support to improve installation 
b.  Check fan blades, bearings, cabinet 

washers, tubing contact and loose 
screws. 

c.  Check for airflow blockage 
 
 
d.  Call service for checking internal 

loose, inadequate lubrication and 
incorrect wirings 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for WINE-MATE VINO1500HZD


























Reviews: