background image

Page 8

shading solutions by

VIMCO

TM

A

C

1 2 3 4

5 6 7 8

Cntrl 1

Cntrl 2

G

rou
nd

AC

AC

Com

MUX

MUX

B

Do not connect if there is only one MDU in the system

. If

there are multiple MDU's in the  system, the MDU's must be wired
together. Connect the MUX, Drain, and MUX terminals of each MDU
together in a daisy chain or homerun configuration.

To a 

Sivoia

®

wall mounted keypad, or a 

Sivoia

®

interface such

as the SV-CCI-GRP or the SV-GRXI. The CNTRL1 and CNTRL2
wires are polarity sensitive.

MDU WIRING - SINGLE MOTOR

Connecting Wires to the MDU Terminal Block

The terminal block located at the bottom of the MDU is the wire
connection point for: power, communication, keypads, and interfaces.

A.

Remove terminal block cover (if not yet removed) by pressing in on
the cover and then pulling downward.

B.

Grasp terminal block and pull down to separate from connecting
block.

C.

Connect wires to the terminal block according to the diagram
below.

D.

Replace the terminal block and the terminal block cover.

Wire to a 

Sivoia

®

plug-in transformer, junction box mount

transformer, or a 

Sivoia

®

power panel. Each MDU must be EARTH

grounded. One 

Sivoia

®

transformer can power 

ONLY ONE MDU

regardless of shade size.

A

B

Control

Comm

Link

Power

Supply

Comm & Power

(         &          combined)

Wire Type

Control

Description

2 conductors / #22-24 AWG

3 conductors (2 shielded, 1 common) / #24 AWG
Belden

®

wire model #1883A

3 conductors #22 AWG

Lutron

model # SV-IR-EXT-10

3 conductors:

2 / #18-22 AWG (24 VAC power supply)
1 / #18-22 AWG (earth ground)

6 conductors:

2 / #16 AWG (24 VAC power supply)
1 / #18 AWG (earth ground)
3 #22 AWG sh 1 #24 AWG common (comm link)

(Lutron wire model no. SV-CBL-MDU-250)

Control to MDU: 250 ft. (76 m)

Max. Length

4000 ft. (1333 m) per system
1000 ft. (333 m) from MDU to MDU

50 ft. (15 m) per system - total of 5
SV-IR-EXT-10, 10 ft. (3 m) each

MDU to 

Sivoia

®

power panel:

200 ft. (61 m)

Transformer to MDU:

#18 AWG - 150 ft. (46 m)
#20 AWG - 100 ft. (31 m)
#22 AWG - 60 ft. (18 m)

A

Comm Link

B

B

D

Power Wires

C

C

SV-IR Extension 
Cable

E

5

Summary of Contents for Lutron Sivoia

















Reviews: