Vimar By-alarm 01727.1, Manual

Page: 3 / 4

Viale Vicenza, 14
36063 Marostica VI - Italy
www.vimar.com 49401438A0 02 1907
By-alarm
01727.1
For details on the configuration of the device, please see also the radio interface 01729 manual.
General configurations
The detectors are configured via six menus; the single options are accessed and set via the push-buttons:
PROG : navigation push-button.
RESET : push-button for restarting the device.
SELECT : push-button for menu selection.
TAMPER : push-button for setting the parameters.
Before configuring the detector it is always necessary to set the relevant parameters.
SETTING PARAMETERS
The device parameters are set with the card inserted in the enclosure so that the tear-proof tamper is closed.
After correctly powering up the device, keeping the PROG push-button pressed, press for 1 s and then
release the RESET button. The three LEDs will emit a fast blink and then go out; this indicates access
to Menu 1. Lastly, release the PROG button.
Selecting the desired menu
To select the desired menu, briefly press the PROG button; each time it is pressed the LEDs change
status, showing the related menu item as shown in the table below:
LEDs on
Descriptions of the menu
R Y G
Menu 1 - IN input and accelerometer function configuration

Menu 2
- Accelerometer sensitivity configuration

Menu 3 - IN input configuration as input or pulse counter
 
Menu 4 - Channel configuration for on-board REED, IN input and accelerometer

Menu 5 - Reed, Tamper and Supervision configuration
 
Menu 6 - Transmission capacity configuration
Legend: R =Red LED, Y =Yellow LED, G =Green LED.
N.B. In the following contents the default configuration is indicated by * .
The R and G LEDs display the selectable options and the Y LED, activated/deactivated with the
TAMPER button, confirms the selected one.
• Menu 1
When all LEDs are off you are in Menu 1.
- Press the SELECT push-button to enter the configuration; the three LEDs will blink 3 times to confirm
the selection made.
- Using the TAMPER push-button to edit and the PROG push-button to scroll through the options, set
the desired function as shown in the table below:
LEDs on
Yellow LED off Yellow LED on
R G
* Accelerometer on Accelerometer off

* Accelerometer as SHOCK Accelerometer as VIBRO

IN: single balancing * Enabling NC or NO
 
IN: normally closed * IN: normally open
- To save and return to the main menu, press the SELECT button; to save and exit configuration com-
pletely, briefly press the
RESET
button.
• Menu 2
When the yellow LED is on you are in Menu 2.
- Press the SELECT push-button to enter the configuration; the three LEDs will blink 3 times to
confirm the selection made.
- For this menu, only one of the functions must be active; using the PROG button, scroll through the
options until you find the desired configuration and press the TAMPER button to confirm the choice
that will be highlighted by the yellow LED coming on .
LEDs on
Functions
R G
Maximum sensitivity

High sensitivity

* Medium sensitivity
 
Minimum sensitivity
- To save and return to the main menu, press the SELECT button; to save and exit configuration com-
pletely, briefly press the RESET button.
• Menu 3
When the green LED is on you are in Menu 3.
- Press the SELECT push-button to enter the configuration; the three LEDs will blink 3 times to confirm
the selection made.
- Using the TAMPER push-button to edit and the PROG push-button to scroll through the options,
set the desired function as shown in the table below:
LEDs on
Yellow LED off Yellow LED on
R G
* IN: external contact IN: pulse counter contact

* 6 pulses in the time window 2 pulses in the time window

Pulse duration 10 ms
* Pulse duration 2
ms
 
* Time window: 20 s Time window: 60 s
- To save and return to the main menu, press the SELECT button; to save and exit configuration com-
pletely, briefly press the RESET button.
• Menu 4
When the green and yellow LEDs are on you are in Menu 4.
- Press the SELECT push-button to enter the configuration; the three LEDs will blink 3 times to
confirm the selection made.
- For this menu, only one of the functions must be active; using the PROG button, scroll through the
options until you find the desired configuration and press the TAMPER button to confirm the choice
that
will be highlighted by the yellow LED coming on
.
LEDs on
Functions
R G
* Channel 1: On-board REED + IN + Accelerometer

Channel 1: On-board REED + IN Channel 2: Accelerometer

Channel 1: On-board REED Channel 2: IN
Channel 3: Accelerometer
- To save and return to the main menu, press the SELECT button; to save and exit configuration
completely, briefly press the RESET button.
• Menu 5
When the red LED is on you are in Menu 5.
- Press the SELECT push-button to enter the configuration; the three LEDs will blink 3 times to confirm
the selection made.
- Using the TAMPER push-button to edit and the PROG push-button to scroll through the options, set
the desired function as shown in the table below:
LEDs on
Yellow LED off Yellow LED on
R G
On-board REED disabled * On-board REED enabled

* Tamper off Tamper on

Supervision off * Supervision on
 
Supervision interval 8 min * Supervision interval 20 min
- To save and return to the main menu, press the SELECT button; to save and exit configuration com-
pletely, briefly press the
RESET
button.
• Menu 6
When the red and yellow LEDs are on you are in Menu 6.
- Press the SELECT push-button to enter the configuration; the three LEDs will blink 3 times to
confirm the selection made.
- For this menu, only one of the functions must be active; using the PROG button, scroll through the
options until you find the desired configuration and press the TAMPER button to confirm the choice
that will be highlighted by the yellow LED coming on .
LEDs on
Functions
R G
* Low power

Medium power

Maximum power
- To save and return to the main menu, press the SELECT button; to save and exit configuration com-
pletely, briefly press the RESET button.
INSTALLING THE DETECTOR
• Install the device as high up as possible.
• As far as possible, install the device upright (battery downwards).
• Install the device on the frame and the magnet on the moving part.
• Do not install the detector in the vicinity of metal objects and devices that generate radio frequencies
such as televisions, computers, routers, hot spots, etc.
The installation procedure is as follows:
1. Configure the detector (see paragraph 9.2 of the radio interface installer manual 01729).
2. Acquire the detector on the radio interface 01729.
3. Secure the detector, provisionally, in the desired location.
4. Run a communication test to ensure proper communication between the detector and the radio
interface 01729. If the test is successful, verified with the red and green LEDs on the detector lighting
up, secure it permanently or, on the contrary, reposition it and perform a new test.
N.B.: Considering the powers involved and the interferences present in the field it is possible that
even the smallest movements of the device may significantly improve or worsen the transmission
quality. It is also important to perform periodic maintenance on the devices to prevent or detect any
possible external interference.
INSTALLATION RULES
Installation should be carried out by qualified personnel in compliance with the current regulations regard-
ing the installation of electrical equipment in the country where the products are installed.
REGULATORY COMPLIANCE
RED directive.
Standards EN 60950-1, EN 50130-4, EN 61000-6-3, EN 301 489-3, EN 300 220-2, EN 62479.
REACH (EU) Regulation no. 1907/2006 – Art.33. The product may contain traces of lead.
Vimar SpA declares that the radio equipment complies with Directive 2014/53/EU. The full text of the EU
declaration of conformity is on the product sheet available at the following Internet address: www.vimar.com.