background image

QUICK RESPONSE  

CONCEALED PENDENT  

SPRINKLERS 

VK4651 (K4.2)

TECHNICAL DATA

The Viking Corporation, 210 N Industrial Park Drive, Hastings MI 49058

Telephone: 269-945-9501  Technical Services: 877-384-5464  Fax: 269-818-1680  Email: [email protected]

Visit the Viking website for the latest edition of this technical data page www.vikinggroupinc.com

Page 3 of 8

Form No. F_040320    21.12.02  Rev 21.3

TABLE 2: COVER PLATE ORDERING INFORMATION

Instructions: 

(1) Select a Cover Plate Base Part Number 

(2) Add the suffix for the desired Finish

(3) Add the suffix for the required Cover Plate Nominal Rating. 

Example: 

23190MC/W = 165 °F (74 °C) Temperature Rated 2-3/4” (70 mm) diameter Round Cover Plate with a Painted White finish.

1: Select a Cover Plate Base Part Number

3

2: Select a Finish

Thread-On Style

Push-On Style

Base Part 

Number

Size

Inch (mm)

Type

Base Part 

Number

Size

Inch (mm)

Type

Description

Suffix

5

23190

2-3/4 (70)

Round

23447

2-3/4 (70)

Round

Polished Chrome

F

23174

3-5/16 (84)

Round

23463

3-5/16 (84)

Round

Brushed Chrome

F-/B

23179

3-5/16 (84)

Square

23482

3-5/16 (84)

Square

Bright Brass

B

23193

4

2-3/4 (70)

Stainless 

Steel Round

23455

2-3/4 (70)

Stainless 

Steel Round

Antique Brass

B-/A

Brushed Brass

B-/B

23183

4

3-5/16 (84)

Stainless 

Steel Round

23473

3-5/16 (84)

Stainless 

Steel Round

Brushed Copper

E-/B

Painted White

M-/W

Painted Ivory

M-/I

Painted Black

M-/B

3: Temperature Rating Matrix

1,2

Cover Plate Nominal 

Rating (Required)

Temperature 

Classification

Sprinkler Nominal Rating

Sprinkler Maximum Ambient 

Ceiling Temperature

2

Suffix

135 °F (57 °C)

Ordinary

155 °F (68 °C)

100 °F (38 °C)

A

165 °F (74 °C)

Intermediate

175 °F (79 °C)

150 °F (65 °C)

C

165 °F (74 °C)

Intermediate

200 °F (93 °C)

150 °F (65 °C)

C

Footnotes

1. 

The sprinkler temperature rating is stamped on the deflector. 

2. 

Based on NFPA-13. Other limits may apply, depending on fire loading, sprinkler location, and other requirements of the Authority Having Jurisdiction. Refer to specific 

installation standards.

3. 

Part number shown is the base part number. For complete part number, refer to current Viking price list schedule.

4. 

Stainless Steel versions are not available with any finishes or paint.

5. 

Where a dash (-) is shown in the Finish suffix designation, insert the desired Temperature Rating suffix. See example above.

Summary of Contents for VK4651

















Reviews: