manualshive.com logo in svg

Viking VK1202, Technical Data Manual

Share
Download
Viking VK1202 Technical Data Manual Download Page 16

XT1 Sprinkler and 

XG Guard Assemblies

BULLETIN

The Viking Corporation, 210 N Industrial Park Drive, Hastings MI 49058

Telephone: 269-945-9501  Technical Services: 877-384-5464  Fax: 269-818-1680  Email: [email protected]

Visit the Viking website for the latest edition of this technical data page www.vikinggroupinc.com

Page 1 of 1

Form No. F_091119    19.09.11     Rev 19.1

1.  INTRODUCTION

The purpose of this bulletin is to inform users of proper XG Guard usage for the  Model XT1 Sprinklers. The XG Guard assemblies 

are specifically listed and approved for use on Model XT1 Sprinklers; no other guard assemblies should be used. 

 

 

WARNING  

Viking sprinklers are manufactured and tested to meet the rigid requirements of the approving agency. The sprinklers 

are designed to be installed in accordance with recognized installation standards. Deviation from the standards or 

any alteration to the sprinkler after it leaves the factory including, but not limited to: unlisted accessories, painting, 

plating, coating, or modification, may render the sprinkler inoperative and will automatically nullify the approval and any 

guarantee made by The Viking Corporation. Refer to the Authority Having Jurisdiction prior to installation.  

2.  GENERAL INFORMATION: 

A potential product performance issue may exist when listed products are combined with unlisted product(s) that have not been 

evaluated together by a recognized approval laboratory. With the development of new products and existing products, it is extremely 

important to correctly match a sprinkler with a sprinkler guard. Please refer to the appropriate manufacturer’s technical literature or 

call Viking Technical Services at 877-384-5464.

  

IMPORTANT

 

Model XT1 sprinklers are specifically listed and approved with XG Guard. The XG Guard, part number 22931, is listed 

and approved for use with the following XT1 sprinklers: VK1001, VK1021, VK3001, VK3021, VK2002, VK2022, VK3502, 

VK3522, VK2001, VK2021, VK3501, VK3521.

Refer to the Guards and Water Shields for XT1 Sprinklers Technical Data Sheet at the following link:  

https://www.vikinggroupinc.com/sites/default/files/documents/021319.pdf

 

Listed and Approved XG Guard/XT1 Sprinkler Assembly

Unlisted Guard/XT1 Sprinkler Assembly

Activation 

element T-hinge 

blocked

Summary of Contents for VK1202

















Reviews:

No comments

Brands by name

Popular brands

Load more brands