C. Programming Examples
Programming the RAD-1 to...
1.
...set the outside line access for this PABX to 9
2.
...set the “Priority 1” access code to 123456
3.
...set the “Priority 2” access code to 234567
4.
...disable the call timer
Enter Digits
9 #44
123456 #45
234567 #46
#48
Quick Programming Features
Security code (6 digits, 0-9) (factory set to 845464) .................................................
Outside line access (used with priority 2 and toll restriction)
(factory disabled)
............
Priority 1 Access Code (6 digits, no digits diables)
(factory disabled)
...........................
Priority 2 Access Code (6 digits, no digits diables)
(factory disabled)
.........................
Call timer (00 for 5 seconds, 01-99 for .5 to 49.5 minutes)
(factory disabled)
..............
Note:
To disable or eliminate the use of any of the above features, enter the #
+ location number (44, 45, 46, or 48) without any preceding numbers.
To restrict 1-900, 976, 1-976, 1-xxx-976
(factory setting)
............................................
To allow 1-900, 976, 1-976, 1-xxx-976 .....................................................................
To restrict 1 + Long Distance, 1-0 (1-800, 1-888 always allowed)
(factory setting)
......
To allow 1 + Long Distance, 1-0 ...............................................................................
To restrict 0 + Dialing (factory setting) ......................................................................
To allow 0 + Dialing ..................................................................................................
To restrict 555, 1-555, 1-xxx-555, 411, 1-411 (factory setting) .................................
To allow 555, 1-555, 1-xxx-555, 411, 1-411 .............................................................
Answer alert tones on (factory setting) .....................................................................
Answer alert tones off ...............................................................................................
SO-24A
mode enable ...............................................................................................
SO-24A
mode disable (factory setting) .....................................................................
Exit Programming and disconnect ...........................................................................
Set all programming features to factory settings .......................................................
6 digits
1 digit
6 digits
6 digits
2 digits
✱
1
✱
2
✱
3
✱
4
✱
5
✱
6
✱
7
✱
8
✱
9
✱
0
✱ ✱
✱
#
# 7
###
#47
#44
#45
#46
#48
Enter Digits
then
then
then
then
then
- then - Enter Memory Location
4.
Operating Features
500ms hookswitch flash on LINE OUT port .......................................................................................................................
2 second momentary disconnect on LINE OUT port ..........................................................................................................
Hang up LINE IN and LINE OUT port .................................................................................................................................
# 1
# 2
# 7
Enter Digits
1. For Accessing PABX Features (DISA) (Section A)
Programming the RAD-1 to...
1.
...disable outside line access
2.
...disable the “Priority 1” access code
3.
...disable the “Priority 2” access code
4.
...set call timer to 1 minute
Enter Digits
#44
#45
#46
02 #48
2. For Accessing One Way Paging Systems (Section B)
Programming the RAD-1 to...
1.
...disable outside line access number
2.
...set the “Priority 1” access code to 345678
3.
...disable the “Priority 2” access code
4.
...set the call timer to 20 minutes
5.
...restrict 1-900, 976, 1-976 and 1-XXX-976
Enter Digits
#44
345678 #45
#46
40 #48
✱
1
3. For Line Extender (Section C)
B. Programming and Remote Access Features
(requires a Touch Tone phone)
If a valid Touch Tone sequence is entered while programming, a double beep will be heard. Three beeps indicate an
error. To begin programming, call the
RAD-1
. When the device answers, you have 20 seconds to enter
✱
followed by
your 6 digit security code (a double beep should be heard). The
RAD-1
may now be programmed.
Note:
While programming, if no Touch Tones are entered for 20 seconds, the
RAD-1
will disconnect.
