Viking MA 339, Instruction Manual

Page: 43 / 588

41
DE
FR
NL
IT
ES
PT
NO
SV
FI
DA
PL
SK
TR
HU
EN
0478 131 9917 G - EN
● Insert left and right clamping pieces (H)
into handlebar console (2) as
illustrated. Fit washer (E) onto
screw (F) and guide screw (F) through
clamping pieces and lower handlebar
from the inside to the outside.
● Fit washer (E).
● Insert pin (G) in quick-clamping
device (I) and screw both together onto
screw (F).
● Close quick-clamping device (3).
● Quick-clamping device (3) must be
sufficiently tightened so that it closes
completely and the handlebar is firmly
attached to the handlebar console. If
necessary, release quick-clamping
device again and tighten or loosen
screw (F).
Installing electric cable:
● Insert electric cable (1) in strain relief
moulding (2) of handlebar console as
illustrated. Make sure the cable tie (3) is
correctly positioned in the strain relief
moulding.
● Press electric cable (1) into holder (4)
on quick-release clamp body. The
electrical cable must lie taught against
the handlebar tube in the area of the
lower handlebar.
7.3 Installing dual handlebar
(MA 339)
Installing upper handlebar:
● Insert flat head bolt (J) through cable
guide (K) and attach electric cable (1).
● Fit dual handlebar (2) onto both lower
handlebar sections (3). Insert flat head
bolts (J) – on right with cable guide (K),
on left without – through bores from the
inside to the outside and tighten with
rotary handles (L).
Installing cable clip:
● Fasten electric cable (1) to upper
handlebar with cable clip (M). Ensure a
distance of 25 - 27 cm between cable
clip and switch on upper handlebar.
7.4 Assembling grass catcher
box
● Fit upper part of grass catcher
box (B) onto lower part of grass catcher
box (C). Ensure correct position in
guides (1).
● Push pin (D) through bores provided
from inside.
● Allow upper part of grass catcher
box (B) to engage in lower part of grass
catcher box using slight pressure.
● Attach grass catcher box ( Ö 9.5).
8. 1 General
The MA 339 and MA 339 C lawn mowers
are operated with rechargeable batteries.
Only high-quality STIHL lithium-ion
batteries of type "AP" are used.
The batteries (supplied in some cases) are
optimally adapted to the intended purpose,
however, all STIHL lithium-ion batteries
available from specialist dealers ( AP 80 ,
AP 11 5 , AP 1 20 , AP 1 60 etc.) may also be
used.
The lawn mower electronics exchange
data with the installed battery and adapt
the power of the electric motor to the
relevant capacity.
8.2 Connecting charger to the
mains
● Insert mains plug (1) in
socket (2).
● After connection of the charger to the
power supply, a self-test is performed.
During this process, the LED (3) on the
charger illuminates green for approx.
1 second, then red, and then
extinguishes again (
Ö 8.6).
8.3 Removing/installing battery
● Open battery compartment
and disconnect safety plug
(
Ö
9.1).
Removing battery:
● Pull out battery (1) upwards.
Installing battery:
● Insert battery (1) into battery
compartment as shown applying slight
pressure and close cover.
8.4 Charging battery
● Remove battery from battery
compartment (
Ö 8.3).
● Connect charger to the mains ( Ö 8.2).
5
8. Battery and charger
6
7
8
9