Description
Enter Digits
+ Location
Speed dial number ............................................................................................................................... 1-32 digit (0-9)
+ #00
Multi-number auto-dialer numbers 1-5 (DIP switch 2 must be
ON
) ...................................................... 1-32 digit (0-9)
+ #01-#05
Q
(anywhere in the speed dial number) ...............................................................................................
# (anywhere in the speed dial number) ...............................................................................................
Q
#
Set dialing speed to normal (Touch Tones: 120ms on/off, Pulse: 10 pps) (factory setting) ..................
Q
1
Set dialing speed to fast (Touch Tones: 50ms on/off, Pulse: 20 pps) ...................................................
Q
2
Block hand held pocket dialers (factory setting) ..................................................................................
Q
3
Allow hand held pocket dialers ............................................................................................................
Q
4
Normal pre-dial pause (approximately 1.4 sec) (factory setting) .........................................................
Q
5
Short pre-dial pause (approximately 800 ms) ......................................................................................
Q
6
To add a one second pause at any point in the dialing string ..............................................................
#7
To add a four second pause at any point in the dialing string ..............................................................
Q
7
Toggle between Pulse and Touch Tone dialing (see section
I
) ............................................................
Q
8
Disable toll restriction (factory setting) ..................................................................................................
Q
9
Enable toll restriction ............................................................................................................................
Q
0
Set default volume 1-4 (1 = min, 4 = max) and control (1 = enabled, 2 = disabled) (factory 1,1) ..... 2 digits (1-4,1-2)
+ #46
Change security code .......................................................................................................................... 6 digits (0-9)
+ #47
To clear the speed dial number and return all programming to factory settings ..................................
###
To set the dialing speed, access the
Programming
mode as shown in section
B
, then choose a speed. To set the dialing speed to
Normal
(Touch Tone: 120ms on/off, Pulse: 10pps), enter
Q
1
. To set the dialing speed to
Fast
(Touch Tone: 60ms on/off, Pulse:
20pps), enter
Q
2
.
OFF ON
DIP
Switches
Internal View of
the K-1900-8-EWP
ON
OFF
DIP
Switches
Internal View of
the K-1900-8
1 2
ON
3
1
2
ON
3
J. DIP Switch Programming
Switch
Position
Description
1
ON
Learn Mode
1
OFF
Normal Operation
(factory setting)
2
ON
Multi-Number Dialer Mode
2
OFF
Normal Operation
(factory setting)
Note:
DIP switch 3 is not used and should remain in the OFF
position.
Note:
Special features such as
Q
, #, a mode change and a pause, use single digits in the programming memory.
E. Dialing Speed
The
K-1900-8
is programmed to hang-up if it detects Touch Tones it did not generate. This helps prevent toll fraud from hand held
dialers. To set the
K-1900-8
to block/allow dialing from external devices, access the
Programming
mode as shown in section
B
,
then choose block or allow. To
Block
hand held dialers, enter
Q
3
. To
Allow
Touch Tones from external devices, enter
Q
4
.
F. Hand Held Pocket Dialers
In the single number auto-dialer mode, the time from when the handset is taken off-hook until the
K-1900-8
auto-dials can be pro-
grammed. Access the
Programming
mode (section
B
), then choose a pause length. To set the pause length to
Normal
(approxi-
mately 1.4 seconds), enter
Q
5
. To set the pause length to
Short
(approximately 800ms) enter
Q
6
.
G. Pre-Dial Pause
To set pauses in the dialing string, access the
Programming
mode as shown in section
B
, then enter
Q
7
to put a 4 second pause
anywhere in the dialing string, or
#7
for a 1 second pause.
H. Pauses in the Dialing String
These examples would be entered after accessing the Programming mode as shown in section
B
.
K. Programming Examples
To Program the K-1900-8 to...
Enter Digits
Enter Location
...Touch Tone dial 555-1234
5551234
#00
...pulse dial 555-1234 followed by a Touch Tone 9
Q
8 5551234
Q
8 9
#00
...clear the speed dial number
#00
C. Programming Features Quick Reference
3
The
K-1900-8
can operate in 3 different modes. With DIP switch
2
set to
OFF
and memory location
#00
cleared, the
K-1900-8
is in
the Standard (Dumb) Phone mode. With DIP switch
2
set to
OFF
and a phone number programmed in memory location
#00
, the
K-
1900-8
is in the Single Number Auto-Dialer mode. With DIP switch
2
set to
ON
, the
K-1900-8
becomes a Multi-Number Auto Dialer.
D. Dialer Modes
When the
K-1900-8
is in the Standard (Dumb) phone mode, some limited toll restriction is available. With toll restriction enabled, the
phone will hang-up if a 0 or 1 is entered as the first digit, or if more than ten digits are entered. Access the
Programming
mode (sec-
tion
B
), then choose enable or disable toll restriction. To set the
K-1900-8
to
Disable
toll restriction, enter
Q
9
. To set the
K-1900-8
to
Enable
toll restriction, enter
Q
0
.
I. Toll Restriction
