- then -
First speed dial number (factory cleared) ...............................................................................
Second speed dial number (factory cleared) ..........................................................................
Third speed dial number (factory cleared) ..............................................................................
Fourth speed dial number (factory cleared) ............................................................................
Fifth speed dial number (factory cleared) ...............................................................................
To clear any speed dial number ..............................................................................................
To add a
,
at any point in the dialing string .............................................................................
To add a # at any point in the dialing string .............................................................................
Add a 4 second pause at any point in the dialing string ..........................................................
Add a 1 second pause at any point in the dialing string ..........................................................
Identification number (factory cleared) ...................................................................................
Maximum call time, 00-99 min (factory set to 3 min, 00 = 30 sec, no digits = disabled) ..........
Maximum ring-no-answer time, 00-99 sec (factory set to 30 sec, 00 = disabled) ...................
Lap counter, 00-99 laps (factory set to 01, 00 = disabled) ......................................................
Inbound rings before answering, 0-9 rings (factory set to 2, 0 = no answer) ...........................
Change the Security code (factory set to 845464) ..................................................................
To Exit Programming ..............................................................................................................
To clear all programming (load factory settings) .....................................................................
0-20 digits
0-20 digits
0-20 digits
0-20 digits
0-20 digits
(no digits)
,,
,
#
,
7
,
8
0-20 digits
2 digits
2 digits
2 digits
1 digit
6 digits
##7
###
#00
#01
#02
#03
#04
#00 - #04
#20
#42
#43
#44
#45
#47
C. Programming Features Quick Reference
Memory
Location
Enter Digits
+
+
+
+
+
+
+
+
+
+
Note:
Up to 20 digits can be stored in each dial position. Special features such as pause, touch tone
,
and # count as single digits.
D. Speed Dial Numbers
To Program the K-1900-30 to...
...to store 555-1234 as the first emergency speed dial number
...to store a touch tone 9, a four second pause and then dial 333-4444
into the second speed dial memory position
...to clear the first speed dial number
Step 1 (see section A)
Enter programming
Enter programming
Enter programming
Step 2 - Enter Digits
5551234#00
9
,
73334444#01
#00
The speed dial number programmed in location
#00
is the number that is dialed when the phone first comes off hook.
Additional speed dial numbers will be dialed when there is no answer or a busy signal is detected. To program, enter
the desired speed dial number followed by the location number (
#00 - #04
). To clear a speed dial location, simply enter
the memory location (
#00 - #04
) alone. The
K-1900-30
is factory set with no speed dial numbers programmed.
E. Identification Number
(memory location #20)
A touch tone I.D. number (up to 20 digits) can be used to identify the call, and is given out when the receiving party
presses a touch tone
,
. To program the optional I.D. number, enter the desired number followed by
#20
.
Example:
To
store 333 as the I.D. number, enter:
333#20
.
F. Maximum Call Time
(memory location #42)
The Maximum Call Time can be used to cut off a call. Once the call is answered, if it lasts longer than the time pro-
grammed in minutes, the phone line will be dropped and a busy signal will be sent to the phone. This two digit number
can range from 01 to 99 minutes or enter 00 for 30 seconds. To disable this feature enter
#42
without any preceding
digits. This time is factory set to
03
(3 minutes). If the
K-1900-30
is being used with a Viking
E-Series
or
K-Series
phones, be sure to disable that phone’s maximum call timer.
B. Security Code
A six digit number may be used to access the programming mode. The security code has been factory set to
845464
(V-I-K-I-NG). It is recommended that you change the security code to a personal 6 digit number as follows:
Step 1.
Access programming as shown in section
A
.
Step 2.
Enter your new security code followed by
#47
.
Step 3.
To exit remote programming, enter
##7
or do not enter any touch tones for at least 20 seconds. To exit local
programming, simply hang up the phone.
Note:
The security code must be six digits in length and
MUST NOT
contain a
,
or
#
. If you have forgotten your
security code, see section “
A. Local Programming
” or “
Remote Programming Without the Security Code
.”
