manualshive.com logo in svg

Viking F20712D, Installation Manual, Page: 13 / 20

Share
Download
Viking F20712D Installation Manual Download Page 13

Door & Drawer Removal 

(cont.)

13

Replace Doors and Hinges

1. Assemble the parts for the top hinge as shown

in Top Hinge graphic. DO NOT tighten the
screws completely.

2. Replace the parts for the bottom hinge as

shown in Bottom Hinge graphic. Tighten
screws. Replace the refrigerator door.

Note:

Provide additional support for the

refrigerator door while the hinges are being
moved. DO NOT depend on the door gasket
magnets to hold the door in place while you
are working.

3. Align the door so that the bottom of the

refrigerator door aligns evenly with the top of
the freezer drawer. Tighten all screws.

4. Reconnect the wiring plug on top of the left-

hand side refrigerator door.

5. Reconnect the water lines by firmly pushing

one line inside the other. Slide the black
locking collar fully forward.

OR

5a.Reconnect the water line by pulling back the 

locking collar ring while firmly pushing the 
water line into the connector.

6. While holding the tabbed section of the

waterline, turn the locking collar
counterclockwise until you hear a “click.”

Note:

The arrow on the tabbed section should

align with the two bars on the locking collar.

7. Check for leaks. Replace the top hinge covers.

Remove and Replace Freezer Drawer

IMPORTANT:

Two people may be required to

remove and replace the freezer drawer. 

Remove Drawer Front

1. Open the freezer drawer to full extension.
2. Loosen the four screws attaching the drawer

glides to the drawer front. See Drawer Front
Removal graphic.

Note:

Loosen screws three to four turns. Keep

the screws in the drawer front.

3. Lift drawer front upward and off the screws.

See Drawer Front Removal graphic.

Replace Drawer Front

1. Slide the drawer glides out of the freezer

compartment. Insert the screws in the top of
the drawer front into the slots in the drawer
brackets. See Drawer Front Replacement
graphic.

2. Pull the drawer brackets toward you to position

the two screws in the bottom of the drawer
front into the brackets. See Drawer Front
Replacement graphic.

3. Completely tighten the four screws.

Drawer Front Removal

A. Loosen 4 Door Bracket Screws

A

Drawer Front Replacement

Summary of Contents for F20712D





















Reviews:

No comments