manualshive.com logo in svg

Viking F-1, Installation Instructions And Safety Information

Share
Download
Viking F-1 Installation Instructions And Safety Information Download Page 13

VIKING TECHNICAL SUPPORT 1.800.908.0884

1 1

Manual Release

When manual operation is required:

1.  Remove the “Output Shaft Cover” or Hat.
2.  Lift the “Manual Release Handle”.
3.  Remove the “Clutch Key”.

To resume normal operation:

1.  Align the notches on the Output Shaft to the clutch 

and reinstall the Clutch Key.

2.  Push the Manual Release Handle down, back to the 

locked position. 

Refer to page 17 for more details

“UL”

 Protects against entrapment in both the opening and closing directions. Input will 

reverse the gate momentarily in the opposite direction it was traveling. Refer to page 28.

“Re-Open”

 Protects against entrapment in the closing direction ONLY. Input will reverse the 

gate all the way to the Open Limit. Refer to page 29.

STEP 1: 

Connect the monitored entrapment protection 

sensor(s) to the Viking control board as illustrated.

STEP 2:

Execute the Learn Process:

•  Toggle the “Diagnose” button 

until you see 

UL LEARN NO LEARN

 

on the LCD Display.

•  Press and hold the “Stop” button.
•  Toggle the “Diagnose” button 

once.

•  The number of Monitored sensors 

connected to the “UL” or Re-
Open terminals will now be 
displayed. 
EXAMPLE:  

UL LEARN

UL2  RO1

UL LEARN

NO LEARN

10K Monitored Terminal

10K Monitored Terminal

IMPORTANT SAFETY INFORMATION

!

WARNING! Not Following these instructions may cause severe injury or death.

!

Cable use in Class 2 circuit to an external device shall be type CL2, CL2P, CL2R, CL2X or other 

cable with equivalent or better electrical, mechanical, and fl ammability ratings.

Monitored Entrapment Protection Installation

!

 

IMPORTANT:

 A minimum of one Monitored External Entrapment Sensor is required to be 

connected to the UL terminal OR the Re-Open terminal. If there is a possible entrapment 
zone in the open direction, an external sensor MUST be wired to the “UL” input or the 
installation will not comply with UL 325.

UL SENSOR ERRORS:

If an problem occurs with one of the monitored 
entrapment sensors, the “Stop” LED will flash and 
an ERR message will be displayed, indicating which 
input terminal(s) the sensor is connected to.

TERMINAL:

“UL”

“Re-Open”

“UL” & “Re-Open”

ERROR
MESSAGE:

ERR SENS
UL

ERR SENS
RO

ERR SENS
UL    RO

Summary of Contents for F-1





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands