5
VIKING
Model:
XXXXXXX
xxxxxx
S/N:
REN 0.8A:
XXXXXXXX
V
iking Electronics, Inc. (715) 386-8861
1531 Industrial St., Hudson, WI 54016
P/N:
DEV
:
Complies with FCC Part 15 and 68 Reg. No: US:AH3TE08A
22264
Back View of the E-70 Circuit
Board Mounting Plate
- Black (GND)
+ Red (5-14VDC)
Green (Date 0)
White (Data 1)
Up to 500 ft
3-Wire Gel-Filled Butt
Connectors included
(3M Scotchlok UR2)
24 Awg Stranded
Shielded Cable
(Belden 9537)
Black
Red
Green
White
STAND-ALONE
DOOR CONTROLLER
ENTRY SYSTEM
VIKING
PROGRAM
PHONE
GANG
PROG
COMM
ELECTRONICS
HUDSON, WI 54016
VIKING
©
MODEL ES-1
POWER 12 VDC
BLK
RED
GRN
WHT
ENTRY POINT
WIEGAND
DEVICE
12V DC
Adapter
Included
Local Touch Tone
Programming Phone
(Power typically
not required for
gate controllers.)
Doorstrike/Magnetic Lock
(not included)
Doorstrike
Power Supply
5A@30VDC/250VAC
maximum
(not included)
or
RAD-1A Remote Access
Device (not included)
Remote Touch Tone
Programming Phone
or
LOG
BUS
Black
Red
Green
White
To Viking model
ES-1 or
Equivalent 26-Bit
Wiegand Card
Reader Controller
Viking Model ES-1 (not included,
see DOD# 193 for more information)
F. Wiring the Proximity Card Reader
A. Adjusting Speaker Volume
B. Adjusting the Microphone Volume
In certain noisy locations (background traffic,
machinery or wind), the microphone volume may
need to be decreased. A symptom of this is one-way
talk path, in which the distant party cannot be heard
over the speaker. A microphone volume pot is pro-
vided for increasing or decreasing the microphone
volume.
Note:
If the microphone volume is set too
high or too low, one-way talk path may occur.
The speaker volume pot can be adjusted to increase
or decrease the speaker volume to the level desired.
VIKING
Model:
XXXXXXX
xxxxxx
S/N:
REN 0.8A:
XXXXXXXX
V
iking Electronics, Inc. (715) 386-8861
1531 Industrial St., Hudson, WI 54016
P/N:
DEV
:
Complies with FCC Part 15 and 68 Reg. No: US:AH3TE08A22264
Rear View of the
E-70 Circuit Board
Mounting Plate
Speaker
Volume
(see section A)
Microphone
Volume
(see section B)
1 2 3 4
ON
DIP
Switches
ON
OFF
Note:
Pots and DIP switches are shown in factory default settings.
P
P
r
r
o
o
g
g
r
r
a
a
m
m
m
m
i
i
n
n
g
g
C. DIP Switch Programming
DIP switch 1 is for turning the Auto Answer feature ON and
OFF. The
E-70
is factory set to auto answer when an inbound
call is detected.
1. Auto Answer Feature ON/OFF (DIP Switch 1)
With DIP switch 2 in the ON position, if the
E-70
detects more
than 5 seconds of continued dial tone, the unit will automati-
cally disconnect. If the
E-70
is installed on a continuously
noisy line, it may detect the noise as dial tone and automati-
cally disconnect. If this happens, turn the dial tone detection
(DIP switch 2) OFF.
2. Dial Tone Detection ON/OFF (DIP Switch 2)
Switch
1
1
2
2
3
3
4
4
Position
ON
OFF
ON
OFF
ON
OFF
ON
OFF
Description
Auto-Answer ON *
Auto-Answer OFF
Dial Tone Detection ON *
Dial Tone Detection OFF
Programming Mode
Normal Operation Mode *
LED On *
LED Off
* Note:
These are the factory settings.
