background image

IMPORTANT

• Before beginning, read these instructions

thoroughly and carefully.

• Installation and service must be

performed by a qualified installer, service
agency, or the gas supplier.

DO NOT

remove permanently affixed

labels, warnings, or plates from the
product as this may void the warranty.

• Observe all local and national codes,

requirements and ordinances.

• Installation must conform with local codes

or in the absence of codes, the National
Fuel Gas Code, ANSI Z223.1- latest
edition and the National Electrical Code,
ANSI/NFPA 70- latest edition.

In Canada:

Installation must be in

accordance with the current CAN/CGA
B149.1 & 2 Gas Installation codes and with
the current CSA C22.1 Canadian Electrical
Codes Part 1 and/or local codes.

• Installation of any gas-fired equipment

should be made by a licensed plumber.

• A manual gas shut-off valve must be

installed in the gas supply line ahead of
the cooktop in the gas stream for safety
and ease of service.

In Massachusetts:

This appliance must be

installed by a licensed plumber or gas-fitter.
A “T” handle manual gas valve must be
installed in the gas supply line to the
appliance.

• Installers should leave these instructions

with the consumer who should retain them
for the local inspector’s use and for future
reference.

3

Please Read and Follow

Your safety and the safety of others is
very important.

We have provided many important safety

messages in this manual and on your

appliance.

ALWAYS

read and obey all

safety messages.

This is the safety alert symbol. This

symbol alerts you to hazards that

can kill or hurt you and others.

All safety messages will be preceded by

the safety alert symbol and the word

“DANGER,” “WARNING” or “CAUTION.”

These words mean:

Hazards or unsafe practices

which WILL result in severe personal

injury or death

DANGER

Hazards or unsafe practices

which COULD result in severe personal

injury or death

Hazards or unsafe practices which

COULD result in minor personal injury

or property damage.

All safety messages will identify the

hazard, tell you how to reduce the chance

of injury, and tell you what can happen if

the instructions are not followed.

WARNING

CAUTION

Summary of Contents for Designer DGVU260-5B

























Reviews: