background image

PRODUCT MANUAL

Designed, Manufactured and Supported in the USA

C O M M U N I C A T I O N   &   S E C U R I T Y   S O L U T I O N S

CTG-2A

Networked Clock Controlled 

Tone / Message Generator

and Master Clock

January 31, 2017

        VIKING

Features

Applications

Specifications

Add Master Clock Controlled CD Quality Tones or

Messages and Emergency Tones to Your Paging System

•  Up to 14 Schedules and up to 1,000 Events
•  6 minutes of CD quality WAV file record time
•  Up to 14 different tones or messages
•  4 programmable trigger inputs for emergency tones, etc.
•  Automatic Day Light Savings Time and leap year correction
•  Programmable NTP Clock synchronization
•  PC programming software included
•  RS485 clock SYNC terminals for remote Master Clock control of

Viking CL Series 

RF synchronized clocks 

•  Non-volatile memory with 4 day clock back up
•  Factory loaded with school/factory tones and evacuation signals

(ANSI S3.41), etc.

•  Remote program via TCP/IP network 
•  Page trigger outputs (12VDC and DPDT relay)
•  Programmable Auxiliary relay contacts (DPDT)
•  24 hour digital clock displays hours & minutes
•  One mono line level pre-amp input and audio output
•  Built-in 1 Watt mono audio amplifier
•  One isolated audio output for PABX / dial access paging
•  Master volume control
•  Programmable volume control per tone/message
•  Time base selection: Network, 50/60Hz or internal
•  Programmable message repeat count for trigger inputs

Internal Clock Backup Time:  

4 days

Power:  

120V AC/13.8V AC 1.25A UL listed adapter provided, max current draw: 650mA

Dimensions:

8.25” x  6.25” x  1.75” (210mm x 159mm x 45mm)

Weight:

3.2 lbs  (1.5 Kg)

Environmental: 

32°F to 90°F (0°C to 32°C) with 5 - 95% non-condensing humidity

Preamp (Audio 1/2) Output:

6V RMS across 600 ohms

Paging Amplifier Output:  

1 watt - powers up to (2) 8 ohm or (12) 45 ohm speakers

Sound Pressure:

85 dB @ 1 meter (loud electronic warble from 25AE paging horn)

Maximum Speaker Output Wire Run:

91m (300 ft), 18 AWG

Maximum Load on Page Trigger Output:

750 ohm (15mA)

WAV File Resolution: 

16 bit or 8 bit

WAV File Sampling Rate:

90 sec. of 44.1K, 3 min. of 22K or 6 min. of 11K

Time Base: 

50/60 Hz or internal with NTP clock sync

Internal Time Base Accuracy:

+/- 2ppm (63 seconds per year) without network time sync

or manual adjustment

Connections: 

29 screw terminal block positions, (1) RJ45 network jack

Viking’s model 

CTG-2A

is a networked clock controlled tone/message

generator designed to provide accurately timed tones and/or messages
over your existing paging system. This provides a cost effective way of
signaling school period changes, factory shifts, breaks, lunch periods,
etc. The 

CTG-2A

has four programmable trigger inputs which are ideal

for triggering emergency alert tones/messages to indicate fire
evacuation, severe weather, lock down, all clear or can be used in store
caster applications for “customer service required” announcements, etc.
The 

CTG-2A

can also be used as a master clock to synchronize Viking

CL Series

wireless clocks (see DOD# 466).

The 

CTG-2A

comes equipped with up to 6 minutes of CD quality WAV

file audio storage for up to 14 different tone/messages. The unit is
factory loaded with common school, business and factory tones but can
be programmed with your custom tones/messages or updated from the
list of WAV files from the Viking web site. 

The 

CTG-2A

can be programmed with up to 14 schedules and up to

1,000 events allowing you to program an entire year or multiple years
of schedules in advance. The 

CTG-2A

’s extremely accurate time base

can be manually synchronized, synchronized with 50 or 60 Hz power
or can be programmed to periodically synchronize to 

network or

internet time.

•  Signal the beginning and end of class periods, breaks and lunch periods for schools

•  Signal the beginning and end of shifts, breaks and lunch periods for factories/businesses

•  Provide trigger controlled emergency alert messages for fire, flood, severe weather, lock

down, etc.

•  Provide messages at specific times for store sales, promotions, closing times, airport

loading zones, etc.

•  Provide Auxiliary contact activation at specific times for specific durations for controlling

lights, cameras, unlocking doors/gates, etc.

•  The 

CTG-2A

can also be used as a Master Clock to synchronize 

Viking CL Series

wireless clocks (

DOD# 466

)

The 

CTG-2A

comes with programming software and a network port to

allow PC programming of timed events, schedules, clock
synchronization, wave file download, message volume, day light
savings time, auxiliary relay control, etc.

Installation requires the assistance of a

Network Administrator / IT Technician.

!

Summary of Contents for CTG-2A





















Reviews: