C. Turning the Alert Tones On/Off for Specific Days of the Week
D. Setting Timed Alert Tones
Note:
If more than 128 events have been entered, a long beep will be heard indicating that the event memory is full.
E. Reviewing and/or Cancelling Timed Alert Tones
F. Adjusting Output Volume
G. Activating Contact Closure Alarm Tones
To activate different sounds, short the corresponding pins with a
dry contact closure as shown right (see
Installation
, section
A
).
Note:
The evacuation sound and siren will be repeated continu-
ously, as long as the closures are maintained.
Step 1.
Press the
MODE
button repeatedly until the
SET DAY
indicator lights. The current day of the week and “
on
” or “
of
” will
be displayed. “
on
” = alert tones are ON and “
of
” = alert tones are OFF for that day of the week.
Step 2.
Pressing the
SINGLE
button will toggle between flashing the day of the week and flashing “
on
” or “
of
”. The flashing por-
tion of the display is the section that can be changed.
Step 3.
With the day of the week flashing, use the
TIME
(
+
and
-/CANCEL
) buttons to select the day of the week you would like
to set to ON or OFF. When the correct day of the week is displayed, press the
SINGLE
button to flash “
on
” or “
of
”. The
day can then be set to ON or OFF by using the
TIME
(
+
and
-/CANCEL
) buttons.
Step 4.
Review your day of the week programming by pressing the
SINGLE
button until the weekday (1-7) is flashing, then incre-
ment through each day of the week with the
TIME
(
+
) button and monitor each day for its on or off setting. Exit the
SET
DAY
mode by simply pressing the
MODE
button.
Step 1.
Press the
MODE
button repeatedly until the
SET EVENTS
indicator lights.
Step 2.
Increase or decrease the event time by pressing the
TIME
(
+
or
-/CANCEL
) button until the desired time is shown.
Step 3.
Move DIP switch 2 to
OFF
for bong alert tones or
ON
for buzzer alert tones (see
Programming
section
J
).
Step 4.
Press one of the single, double, or triple
ALERT TONES
buttons to program the number of alert tones you wish to out-
put at the specific event time. A single, double, or triple confirmation beep should be heard.
Step 5.
Repeat steps 2-4 for the remainder of your scheduled events.
Step 1.
Press the
MODE
button repeatedly until the
REVIEW/CANCEL
indicator lights.
Step 2.
Press one of the
ALERT TONES
buttons (single, double, or triple) repeatedly to rotate through the event times associ-
ated with that alert tone button. A red LED at the bottom right corner of the time display will light to indicate a buzzer
event time (versus a bong event).
Note:
Event times are stored in the order of programming, not chronologically.
Step 3.
Press the
-/CANCEL
button to permanently cancel an event tone. A single acknowledgement tone will be heard. The
next consecutive event for that specific alert tone will then be displayed.
Step 4.
Repeat steps 2-3 as needed to remove the events to be cancelled.
Step 5.
When all events for a given alert tone have been cancelled, the display shows three dashes (- - -).
Step 1.
Short pins
9
and
12
together momentarily. The doorbell sound will then chime once.
Step 2.
Adjust the volume control potentiometer (see
Installation
).
Step 3.
Repeat steps 1-2 until the desired volume is achieved.
Sound
Short Pins...
Doorbell (Ding Dong)
...9 to 12
Evacuation Sound (Slow Whoop)
...10 to 12
Siren (Yelp)
...11 to 12
5
