VIKING
MODEL
C-1000
DOOR ENTRY
CONTROLLER
PWR
DEV 2
DEV 1
PHONES
Printed in the U.S.A.
ZF280295 Rev E
Fax Back Doc # 155
Due to the dynamic nature of the product design, the information contained in this document is subject to change without notice. Viking
Electronics, its affiliates and/or subsidiaries assume no responsibility for errors and/or omissions contained in this information. Revisions of
this document or new editions of it may be issued to incorporate such changes.
Product Support Line...(715) 386-8666 Fax Back Line...(715) 386-4345
Operation
A. Placing C.O. Line Calls On Hold
B. Activating the Door Strike
C. Monitoring A Doorbox
D. Features
Activate relay 1 or 2 ....................................................................................
Continuously activate relay 1 or 2 ...............................................................
Continuously de-activate relay 1 or 2 .........................................................
Toggle relay from last position/activate second relay
(shared relay mode)
...
Answer or disconnect a doorbox call ..........................................................
Monitor doorbox 1 .......................................................................................
Monitor doorbox 2 .......................................................................................
Touch Tones
If a C.O. line call is in progress and a doorbox is initiated, a single or double “call waiting” tone will be heard indicating doorbox
1 (DEV 1) or doorbox 2 (DEV 2) is calling. To place the in-progress call on hold and answer the calling doorbox, simply dial a
Touch Tone “#”, pulse dial a “2” or hook flash twice.
To activate a relay contact, you must be communicating with a doorbox. Simply Touch Tone dial “
✱ ✱
”, pulse dial a “3” or hook
flash three times. Two confirmation tones will be heard and the relay will be activated for the programmed contact closure time.
The phone will then be returned to the C.O. line and the original caller will be taken off hold to continue the conversation. To
return to the original call without activating a relay, Touch Tone dial “#”, pulse dial a “2” or hook flash twice.
A doorbox may be turned on for monitoring purposes by Touch Tone dialing a “#” followed by a Touch Tone “1” or “2” to
activate doorbox 1 or doorbox 2 respectively. This feature is not available for pulse dialing phones.
Note: Do not attempt doorbox monitoring while a call is in progress, the call will be disconnected.
These commands will only function while communicating with a doorbox.
✱ ✱
pulse dial 3 or hook flash 3 times
✱
1
✱
0
✱
#
# pulse dial 2 or hook flash 2 times
# 1
# 2
Programming
ON/OFF
OFF - .5 seconds
ON - 10 seconds
OFF - Normal Mode
ON - Learn Mode
OFF - Line Concentrator Mode
ON - Normal Operation Mode
Switch
1
2
3
Description
ClosureTime
Learn Mode
Mode Selection
Pulse
A. Programming the C-1000
1. Enter the Programming mode by going off-hook and entering
✱
followed by the security code (factory set to 845464), a
double beep will be heard. Alternatively, move DIP switch 2 from OFF to ON while on-hook, then go off hook, a double beep
will be heard.
Note: Call in from another line to avoid C.O. tones.
2. To change the security code, enter 6 digits (0 - 9) followed by #47.
3. To program the closure time for device 1, enter 2 digits followed by #01 (see chart to right).
4. To program the closure time for device 2, enter 2 digits followed by #02 (see chart to right).
5. Operation modes may be set while in the programming mode. Follow the steps below:
a. To change programming, reset the C-1000 to factory settings by pressing
✱
0.
b. Change operational modes by entering the codes listed in the chart below left.
Digits
00
01
02
03
04
05
06
07
08
09
10
Seconds
.5
1
2
3
4
5
6
7
8
9
10
Mode
Factory Default
Doorbell Mode
Custom Ring Mode
Shared Relays Mode
Paging Mode
Description
Sets mode to factory default
Doorbox does not ring through to phones
Double ring from device ports
One doorbox utilizes both relay closures
C.O. line held, allows page, press # to return
to line
Digits
✱
0
✱
1
✱
2
✱
3
✱
4
6. To change DIP switches, use the chart to the right.
Note: To prevent
phones from ringing,
the C-1000 could be
operated in the
doorbell mode, see
Programming.
VIKING
ELECTRONICS
HUDSON, WI 54016
MODEL K-600D
1 2 3 4 5
LINE INPUT
NIGHT BELL OVER
PAGING ADAPTER
VOLUME
TONE
VIKING
Two-Line
Adapter
G/R
Inline Coupler
Radio Shack
part # 279-358
2. Multiple Doorboxes Ringing a Doorbell
(1)
(1)
(1)
(1)
Note: When on the C.O., if a Touch Tone other than # is entered, any additional Touch Tones in that dial string will be ignored. To regain
control of the C-1000 , the phone must be momentarily placed on-hook.
(2)
(2)
When a relay is de-activated, a single beep is heard in place of the two conformation tones.
Y/B
Doorbell
Radio Shack
part # 43-1383
(1)
(2)
13.8V AC