background image

VIGOR ELECTRIC CORP.  

VB-4DA

4-Channel Analog Outputs Module

1.  Introduction

The VB-4DA analog output module has four output channels.  The output channels take in a 
digital value and output an equivalent analog (voltage or current) signal.  This is called a D/A 
conversion.  The VB-4DA has maximum resolution of 8 bits.

The selection of voltage or current based output is by user wiring.  Analog ranges of 0 ~ 10 V 
DC and/or 0 ~ 20 mA  maybe selected independently for each channel.

The VB-4DA analog output module is attached as an extension to the VB series Programmable 
Logical Controller (hereinafter referred to as “PLC”), and the VB-4DA is attached as an 
extension to the VB series PLC Main Unit.  Each VB-4DA functions as a special module 
which transfers data with the PLC using the FROM / TO instructions, and would not occupy 
any input or output point.  Up to 8 special modules can be connected to single VB2 series PLC; 
a single VB0 series PLC can connect with two special modules.

2.  Specifications

<< Power Requirement >>

 

5 V DC, 30 mA (for internal control)

          Supplied from PLC Main Unit (or Expansion Unit / VB-PWR) via its extension cable.

   

○  From a Main Unit:

          [ (The amount of Expansion Modules) + (The amount of Special Modules) X 2  ] 

 4

   

○  From an Expansion Unit or VB-PWR:

          [ (The amount of Expansion Modules) + (The amount of Special Modules) X 2  ] 

 12

 

24 V DC (+20% / -15%), 120 mA Max.  (for analog signal output)

Supplied from external power supply or 24 V DC output of PLC.

<< Analog Output Performance Specifications >>

Item

Voltage Output

Current Output

Voltage or Current outputs are selected by BFM #0 & different terminals

Mode

0

1

2

4

5

Analog Output Range (DC)

0 ~ +10 V

0 ~ +5 V

+1 ~ +5 V

0 ~ +20 mA +4 ~ +20 mA

Digital Input Range

0 ~ +250

0 ~ +250

External Load Resistance

500 Ω ~ 1 MΩ

500 Ω or less

Resolution

40 mV

20 mV

16 mV

80 μA

64 μA

Overall Accuracy

± 1% (full scale)

Conversion Speed

0.8 ms / 4 points

Isolation

Photocoupler isolation between analog and digital circuits.  

DC/DC converter isolates of power from its power source.  

No isolation between analog channels.

----------------------------------------------------------------  

  2   

 ----------------------------------------------------------------

Summary of Contents for VB - 4DA









Reviews: