manualshive.com logo in svg

Viglen Vig711W, Manual, Page: 6 / 51

Share
Download
Viglen Vig711W Manual Download Page 6

V1.0                                   Vig711W Motherboard Manual 

5 

Feature Summary

 

 

Form factor: 

 

 

Thin Mini-ITX Form Factor: 170mm x 170mm 

 

Processor: 

 

 

Intel

®

 

Core™ i7, Intel

®

 

Core™ i5, Intel

®

 

Core™ i3, Intel

®

 Pentium

®

, Intel

®

 

Celeron

®

 processors in an LGA1150 socket 

 

Integrated graphics processing (processors with Intel

®

 Graphics Technology) 

 

External graphics interface controller 

 

Integrated memory controller 

 

Chipset 
 

 

Intel

®

 H81 Express Chipset 

 

Memory 

 

Two SO-DIMM Slots 

 

Memory Module (SO-DIMM) sockets 

– only supports Voltage 1.5V 

 

Support for DDR3 1066/1333/1600 MHz SO-DIMMs  

 

Maximum 32GB Memory Size 

 

Graphics 

 

  Integrated graphics support for processors with Intel

®

 graphics technology 

  1x HDMI

®

 port supporting a maximum resolution of 1920x1200@60HZ 

 

Audio 

 

 

Integrated HD audio codec by Realtek

®

 ALC662 

 

Support JACK detection, multi-streaming and anti-pop functions 

 

With ALC105 amplifier to support speakers 

 

Front panel header 

 
LAN 

 

Gigabit (10/100/1000 Mbits/s) LAN subsystem using the Realtek

®

 RTL8111F 

Gigabit Ethernet Controller 

 

Rear I/O Ports 

  1 x 19V Power Port 

  1x HDMI  

  1x Gigabit LAN (Realtek® RTL8111F) 

  1x Microphone 

  1x  Headphone/Speaker 

  2x USB 3.0 Ports 

  2x USB 2.0 Ports 

 

 
 

Summary of Contents for Vig711W




















































Reviews:

No comments